An active balancer with rapid bidirectional charge shuttling and adaptive equalization current control for lithium-ion battery strings

This article proposes an active balancer, which features bidirectional charge shuttling and adaptive equalization current control, to fast counterbalance the state of charge (SOC) of cells in a lithium-ion battery (LIB) string. The power circuit consists of certain bidirectional buck-boost converters to transfer energy among the different cells back and forth. Owing to the characterization of the open-circuit voltage (OCV) vs SOC in LIB being relatively smooth near the SOC middle range, the SOC-inspected balance strategy can achieve more precise and efficient equilibrium than the voltage-based control. Accordingly, a compensated OCV-based SOC estimation is put forward to take into account the discrepancy of SOC estimation. Besides, the varied-duty-cycle (VDC) and curve-fitting modulation (CFM) methods are devised herein to tackle the problems of slow equalization rate and low balance efficacy, which arise from the diminution in balancing current as the SOC difference between the cells decreases in the later duration of equalization especially. The proposed strategies have taken the battery nonlinear characteristic and circuit parameter nonideality into account and can adaptively modulate the duty cycle with the SOC difference to keep balancing current constant throughout the balancing cycle. Simulated and experimental results are given to demonstrate the feasibility and effectiveness of the same prototype constructed. Compared with the fixed duty cycle and the VDC methods, the proposed CFM has the best balancing efficiency of 81.4%, and the balance time is shortened by 27.1% and 18.6%, respectively.     

Picosecond laser trimming of ceramic cores with porous multi-scale particle microstructure

The ceramic core, produced by hot injection molding, is one of the critical components for manufacturing high-performance aircraft engine turbine blades. However, the injection molding process will cause defects such as burrs and flashes in the fine structure of the formed ceramic core. Manual trimming is necessary, but the trimming quality is poor, and the yield is low. In this paper, the online trimming method of ceramic cores is studied. Based on the orthogonal experiment method, the optimal laser parameters for processing the ceramic core's porous multi-scale particle structure material were obtained. Further, the problems of the match head and tail phenomenon and dimensional accuracy improvement in trimming ceramic cores have been studied. A path optimisation method is proposed to improve the quality and accuracy of the trimming profile effectively. Finally, the overall process flow of ceramic core trimming is elaborated, and experimental verification is given. The results show that the ceramic core online trimming method proposed in this paper has advantages of high precision and high yield compared with the manual method, which will have substantial potential application value in the aviation field.     

Farmers' preferences for adopting on-farm concentration of raw milk: Results from a discrete choice experiment in Germany

Milk concentrates are used in the manufacturing of dairy products such as yogurt and cheese or are processed into milk powder. Processes for the nonthermal separation of water and valuable milk ingredients are becoming increasingly widespread at farm level. The technical barriers to using farm-manufactured milk concentrate in dairies are minimal, hence the suspicion that the practice of on-farm raw milk concentration is still fairly uncommon for economic reasons. This study, therefore, set out to investigate farmers' potential willingness to adopt a raw milk concentration plant. The empirical analysis was based on discrete choice experiments with 75 German dairy farmers to identify preferences and the possible adoption of on-farm raw milk concentration. The results showed that, in particular, farmers who deemed the current milk price to be insufficient viewed on-farm concentration using membrane technology as an option for diversifying their milk sales. We found no indication that adoption would be impeded by a lack of trustworthy information on milk processing technologies or capital.     

Effects of spinosad and spinetoram on larval mortality,adult emergence,progeny production and mating in Cadra cautella (Walk.) (Lepidoptera: Pyralidae)

The bacterial formulations, spinosad and spinetoram, were evaluated for their efficacy in suppressing development and mating success in Cadra cautella (Walk.) (Lepidoptera: Pyralidae), the almond moth. A dilution series of spinosad and spinetoram was sprayed on rice flour. Rice flour samples sprayed with water served as the control. Late instar C. cautella larvae were introduced onto spinosad-, spinetoram-, or water-treated rice flour. The first experiment tested the effects of spinosad and spinetoram on larval mortality, as well as emergence of adults and progeny at different insecticide concentrations. In the second experiment, the mating success of C. cautella adults that had emerged from larvae exposed to spinosad was tested inside a cubicle. Both spinosad and spinetoram increased larval mortality, whereas both compounds reduced adult emergence and progeny production. Natural mating was reduced in the presence of the synthetic sex pheromone (Z,E)-9,12-tetradecadienyl acetate. However, exposure of C. cautella larvae to spinosad did not alter mating in adult progeny. Spinosad was more effective than spinetoram at suppressing C. cautella development. The study concludes that both spinosad and spinetoram suppress the development of immatures of C. cautella to the adult stage as well as mating. Thus, the both compounds can be used to protect stored grains from infestation by C. cautella.     

深部松软煤层钻孔孔周煤体变形产渣特征研究

针对煤矿井下高瓦斯软煤顺层长钻孔排渣困难、成孔率低、施工困难等问题,通过数值模拟实验研究了井下深部软煤体变形破坏特征,分析了顺层长钻孔孔周松软煤体变形特征及应力变化,以揭示顺层长钻孔孔周松软煤体变形产渣规律。研究表明:深部高瓦斯软煤顺层钻孔孔周煤体的应力平衡临界条件破坏后将发生大体积突然垮落;钻孔水平最大变形位移为1.22mm,垂直方向最大变形位移为10.7mm;径向孔周煤体垂向变形呈现逐渐减小趋势,且垂向变形明显大于钻孔水平变形。在水平方向上,钻孔孔周煤体应力分布呈现先增大再逐渐减小的变化规律,径向距离对水平应力分布的影响逐渐减小;随着径向距离的增加,钻孔孔周煤体应力分布逐渐降低,钻孔孔壁处煤体的应力出现最大值,且垂直方向处应力值最大。     

Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

Industry 4.0: a supply chain innovation perspective

The Fourth Industrial Revolution – also known as Industry 4.0 (i4.0) – comprises the digitalisation of the industrial sector. This paper uses the theoretical lens of supply chain innovation (SCI) to investigate the implications of i4.0 on supply chain management. For these purposes, the method of structured content analysis is applied to more than 200 use cases of i4.0-enabled SCI introduced by both established and startup companies. i4.0-enabled SCI manifests along three dimensions: process, technology, and business architecture. The key findings of this study can be summarised as follows: first, i4.0-enabled SCI extends the initial focus on productivity improvements in SC processes towards scalability and flexibility. Second, extant i4.0 solutions rely mostly on analytics and smart things while omitting smart people technology and the human-centric approach associated with the i4.0 paradigm. Third, established companies adopt i4.0 merely to sustain their existing business architectures while startup companies radically change their operating models, relying heavily on data analytics and the platform economy. Consequently, established companies pursue a problem-driven, engineering-based approach to SCI while startup companies follow an ‘asset-light’, business-driven approach. Lastly, there are two distinct approaches to digitalising operational SC processes: platform-based crowdsourcing of standard processes and on-demand provision of customised services.     

Synthesis of Ionic Ultramicroporous Polymers for Selective Separation of Acetylene from Ethylene

The design of highly stable and efficient porous materials is essential for developing breakthrough hydrocarbon separation methods based on physisorption to replace currently used energy-intensive distillation/absorption technologies. Efforts to develop advanced porous materials such as zeolites, coordination frameworks, and organic polymers have met with limited success. Here, a new class of ionic ultramicroporous polymers (IUPs) with high-density inorganic anions and narrowly distributed ultramicroporosity is reported, which are synthesized by a facile free-radical polymerization using branched and amphiphilic ionic compounds as reactive monomers. A covalent and ionic dual-crosslinking strategy is proposed to manipulate the pore structure of amorphous polymers at the ultramicroporous scale. The IUPs exhibit exceptional selectivity (286.1–474.4) for separating acetylene from ethylene along with high thermal and water stability, collaboratively demonstrated by gas adsorption isotherms and experimental breakthrough curves. Modeling studies unveil the specific binding sites for acetylene capture as well as the interconnected ultramicroporosity for size sieving. The porosity-engineering protocol used in this work can also be extended to the design of other ultramicroporous materials for the challenging separation of other key gas constituents.     

Exploring design trade-offs for achieving social inclusion in multi-tiered design problems

ABSTRACT

The digital age of the future is ‘not out there to be discovered’, but it needs to be ‘designed’. The design challenge has to address questions about how we want to live, work, and learn (as individuals and as communities) and what we value and appreciate, e.g.: reflecting on quality of life and creating inclusive societies. An overriding design trade-off for the digital age is whether new developments will increase the digital divide or will create more inclusive societies. Sustaining inclusive societies means allowing people of all ages and all abilities to exploit information technologies for personally meaningful activities. Meta-design fosters the design of socio-technical environments that end-user developers can modify and evolve at use time to improve their quality of life and favour their inclusion in the society. This paper describes three case studies in the domain of assistive technologies in which end users themselves cannot act as end-user developers, but someone else (e.g.: a caregiver or a clinician) must accept this role requiring multi-tiered architectures. The design trade-offs and requirements for meta-design identified in the context of the case studies and other researchers’ projects are described to inform the development of future socio-technical environments focused on social inclusion.     

Off‐grid DoA estimation method of wideband signals

In this paper, an off‐grid direction of arrival (DoA) estimation method is proposed for wideband signals. This method is based on the sparse representation (SR) of the array covariance matrix. Similar to the time domain DoA estimation methods, the correlation function of the sources was assumed to be the same and known. A new measurement vector is obtained using the lower‐left triangular elements of the covariance matrix. The DoAs are estimated by quantizing the entire range of continuous angle space into discrete grid points. However, the exact DoAs may be located between two grid points; therefore, this estimation has errors. The accuracy of DoA estimation is improved by the minimization of the difference between the new measurement vector and its estimated values. Simulation results revealed that the proposed method can enhance the DoA estimation accuracy of wideband signals.