Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

凤滩水电厂自动发电控制策略

介绍了凤滩水电厂自动发电控制(AGC)策略的实现方法,重点介绍了修正等容量比例有功分配方法及相应措施.程序设计的原则是,机组紧跟目标负荷的情况下,在最佳效率下运行,同时减少机组开/停机次数、有功调节频率和跨越振动区次数,从而减少机组磨损,兼顾运行效率和机组运行安全.     

Lactic acid production from dining‐hall food waste by Lactobacillus plantarum using response surface methodology

BACKGROUND: Food waste generally has a high starch content and is rich in nutritional compounds, including lipids and proteins. It therefore represents a potential renewable resource. In this study, dining‐hall food waste was used as a substrate for lactic acid production, and response surface methodology was employed to optimise the fermentation conditions. RESULTS: Lactic acid biosynthesis was significantly affected by the interaction of protease and temperature. Protease, temperature and CaCO₃ had significant linear effects on lactic acid production, while α‐amylase and yeast extract had insignificant effects. The optimal conditions were found to be an α‐amylase activity of 13.86 U g^?1 dried food waste, a protease activity of 2.12 U g^?1 dried food waste, a temperature of 29.31 °C and a CaCO₃ concentration of 62.67 g L^?1, which resulted in a maximum lactic acid concentration of 98.51 g L^?1 (88.75% yield). An increase in inoculum size would be appropriate for accelerating the depletion of initial soluble carbohydrate to enhance the efficiency of α‐amylase in dining‐hall food waste fermentation. CONCLUSION: A suitable regression model for lactic acid production was developed based on the experimental results. Dining‐hall food waste was found to be a good substrate for lactic acid fermentation with high product yield and without nutrient supplementation. Copyright © 2008 Society of Chemical Industry     

A novel direct aerodynamically assisted threading methodology for generating biologically viable microthreads encapsulating living primary cells

In a recent discovery, coaxial electrospinning was explored to encapsulate living organisms within a continuous bio‐polymeric microthread from which active biological scaffolds were fabricated (Townsend‐Nicholson and Jayasinghe, Biomacromolecules 2006, 7, 3364). The cells were demonstrated to have gone through all expected cellular activity without their viability being compromised. These biologically active threads and scaffolds have direct and tremendous applicability from regenerative to therapeutic medicine. Currently these post‐processed cells as composite threads and scaffolds are being investigated in‐depth at a cellular level to establish if the processing methodology has any affect on the cellular make‐up. We now demonstrate a competing non‐electric field driven approach for fabricating composite threads and scaffolds influenced only by a differential pressure. We refer to this novel composite thread to scaffold fabrication methodology as coaxial aerodynamically assisted bio‐threading (CAABT). Our investigations firstly, demonstrate that this technique can process handle living organisms without biologically perturbing them in anyway. Secondly the process is elucidated as possessing the ability to form composite active threads from which biologically viable scaffolds are formed. Finally our study employs florescent activated cell sorting (FACScan), a method by which the cellular dynamics and viability are quantified on control and threaded cellular samples at two prescribed time points. In parallel with FACScan, optical comparison of cellular morphology at three time points within a period of three weeks is carried out to photographically observe any changes in the post‐processed cellular phenotype. Our developmental investigations into this novel aerodynamically assisted threading methodology has unearthed a unique biomicrofabrication approach, which joins cell electrospinning in the cell threading to scaffold fabrication endeavor. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Development of a predictive model for polymer/solvent diffusion coefficient calculations

A new calculation procedure for free‐volume parameters is considered in this work by using viscosity prediction methods and the Levenberg‐Marquardt calculation scheme. All parameters used in the Vrentas–Duda free‐volume theory can be estimated from pure component properties. The prediction results are compared with experimental data for some polymer/solvent systems. The diffusion coefficient calculated by Vrentas–Duda theory can be used in the modeling of membrane separation processes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of polyurethane resins and its improvement on dimensional stability and finishing performances of medium‐ and small‐diameter softwoods

This study analyzed the effects of polyurethane (PU) resin treatments on surface homogeneity, dimensional stability, and finishing performances of medium‐ and small‐diameter softwoods produced in Taiwan. Two‐pack PU resins were prepared by combing short castor oil‐modified alkyd resin serving as a polyol with polymeric 4,4′‐diphenymethane diisocyanate (PMDI) serving as a hardener, by the molar ratio of NCO/OH+COOH of 1.2. Four types of short oil‐modified alkyd resins with different polyhydric alcohols (glycerin and pentaerythritol) and polybasic acids (phthalic anhydride and isophthalic acid) were synthesized. Three kinds of medium‐ and small‐diameter softwoods, including China fir, Taiwanina, and Japanese fir with a diameter of 10–15 cm were obtained from Hui‐Sun Forest Station, Taiwan. The wood coating of nitrocellulose (NC) lacquer including sanding sealer and top clear was used. Results show that the surface hardness, homogeneity, moisture excluding efficiency, and antiswelling efficiency of woods were enhanced by PU resin treatments. Among all the PU resins, the isophthalic acid and pentaerythritol‐containing PU resin (IPA‐P‐MDI) achieved the best improved efficiency on dimensional stability of woods. Results of two types of finishing procedure, i.e. NC lacquer sanding sealer plus top clear and top clear only, applied onto the PU‐treated woods revealed that the hardness, adhesion, and durability of NC lacquer films on the PU‐treated wood were superior to those of untreated one, especially for top clear finishing alone. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Novel approach in investigation of the poly(acrylic acid) hydrogel swelling kinetics in water

The swelling kinetics curves of structurally defined poly(acrylic acid) hydrogel in bidistilled water at temperatures: 25, 30, 35, 40, and 45°C were determined. The possibility of kinetically explaining the isothermal swelling process by applying the following models: reaction controlled by diffusion, first order chemical reaction kinetics, and second order chemical reaction kinetics, was investigated. It was found that kinetically explaining the swelling process using these methods was limited to only certain parts of the process. The swelling process in bidistilled water was described in full range assuming that the hydrogel's swelling rate was a kinetically controlled reaction by the rate of the movement of reactive interface of hydrogel. Based on that model, the kinetic parameters, activation energy (E_a) and preexponential factor (A), of the swelling process were determined to be E_a = 35 kJ/mol and lnA = 8.6. A possible mechanism of the investigated swelling process was discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Microwave heating of poly(ethylene terephthalate) bottle preforms used in the thermoforming process

Thermoforming (free blowing) of poly(ethylene terephthalate) preforms was successfully and quickly performed in a rotating system designed for dielectric hysteresis heating. Temperature profile modeling was carried out with the amorphous poly(ethylene terephthalate) permittivity at different temperatures. The Maxwell and heat equations were used to determine the best profile and power tuning. The determination of the theoretical boundary conditions was accomplished by the adjustment of the numerical transient external surface wall temperature with experimental infrared pyrometry results. In comparison with infrared, microwaves allowed high power density absorption inside the perform wall without a dramatic temperature gradient. Consequently, the heat blowing stage could be accelerated, and the process took at least 5 times less energy than infrared heating. Industrial applications involve the integration of the molding step and the design of the overall process. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Intercalated clays from pentaerythritol stearate for use in polymer nanocomposites

Smectite clays treated with quaternary ammonium salts have been utilized for decades in paints, greases, cosmetics, and personal care products as rheological modifiers. They have also been used in industrial wastewater treatment extensively. In more recent times these surface modified clays have demonstrated benefits in polymer/clay nanocomposites. The use of quaternary ammonium modifiers limits the usefulness of these composites in food packaging because they are not approved for direct food contact. It would be advantageous to have surface modifying chemicals acceptable for direct food contact in these composites. This article reports research conducted on a promising surface modifier pentaerythritol stearate (PS), which is approved by the FDA for inclusion in food as a preservative. The surface modification of montmorillonite with PS is reported in detail as well as the production of nanocomposites with selected polymers made with the modified clay. Molecular modeling and purification of commercial PS samples indicate that the mono‐ and diesters are the critical surface modifiers, although the as received commercial material works well in forming intercalated clay complexes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The synthesis of block copolyetherketones based on 4,4′‐dichlorodiphenylketone,phenolphthaleine, and bisphenol A and investigation of their properties

Block structured polyethers based on phenolphthaleine, 4,4′‐dichlorodiphenylketone, and bisphenol A with different degrees condensation (n = 1, 5, 10, and 20) were synthesized by means of acceptor‐catalytic polycondensation. Equaimolar quantities of chloranhydrides of iso‐ and terephthalic acids were used. Higher molecular masses were obtained from longer oligoketones with higher condensation degrees. Better molecular packing, increased thermal and mechanical properties were obtained with higher condensation degrees of oligoketones. © 2007 Wiley Periodicals, Inc. JAppl Polym Sci, 2008