Deposition of thin film silicon using the pulsed PECVD and HWCVD techniques

We report on the use of pulsed plasma-enhanced chemical vapor deposition (P-PECVD) technique and show that “state-of-the-art” amorphous silicon (a-Si:H) materials and solar cells can be produced at a deposition rate of up to 15 Å/s using a modulation frequency in the range 1–100 kHz. The approach has also been developed to deposit materials and devices onto large area, 30 cm×40 cm, substrates with thickness uniformity (<5%), and gas utilization rate (>25%). We have developed a new “hot wire” chemical vapor deposition (HWCVD) method and report that our new filament material, graphite, has so far shown no appreciable degradation even after deposition of 500 μm of amorphous silicon. We report that this technique can produce “state-of-the-art” a-Si:H and that a solar cell of p/i/n configuration exhibited an initial efficiency approaching 9%. The use of microcrystalline silicon (μc-Si) materials to produce low-cost stable solar cells is gaining considerable attention. We show that both of these techniques can produce thin film μc-Si, dependent on process conditions, with 1 1 1 and/or 2 2 0 orientations and with a grain size of approx. 500 A. Inclusion of these types of materials into a solar cell configuration will be discussed.     

螺栓角钢钢节点的三维非线性有限元分析

对螺栓角钢钢节点半刚性连接采用非线性有限元分析方法 ,对连接中的主要构件的顶部、底部、腹板角钢、高强螺栓、梁翼缘、柱翼缘和柱翼缘加劲肋进行三维非线性有限元精细模拟 ,针对有无柱加劲肋、有无腹板角钢等几种连接的情况进行比较分析 ,探讨了螺栓角钢半刚性连接的受力性能。     

Single and matrix HgCdTe photovoltaic detectors

The recent researches and technological developments of middle and long wavelength infrared HgCdTe photovoltaic detectors are presented. Structure, topology, design and performance of HgCdTe photodiodes, silicon readout electronics, Focal Plane Arrays both staring and time delay and integration types, thermal imagers are discussed. Negative differential conductance, bistability and high frequency oscillations under background infrared radiation in HgCdTe photodiodes are reported.     

温度应力、自收缩对高性能混凝土早期开裂的影响

根据高性混凝土的水化特性、物理力学特性及自收缩特性，分析了高性能混凝土早期开裂机理和影响早期开裂的主要因素．并结合工程实例，借助混凝土温度和应力有限元仿真计算方法分析研究了表面适度保温和水管冷却技术在高性能混凝土温控防裂中的应用效果．研究结果表明，表面适度保温与水管冷却相结合能有效降低混凝土的内外温差，减小混凝土早期表面拉应力与后期内部拉应力，防裂效果明显，对类似的工程具有借鉴作用．     

The impact of roasting on the ochratoxin A content of coffee

Roasting coffee led to a drop in the ochratoxin A (OTA) concentration, as measured by the reference method, especially for dark type roasts. The way the beverage was prepared also affected the OTA content, which could paradoxically be higher than that of the initial roasted coffee. Assays on the thermal stability of pure OTA showed that it ought to be found in larger quantities in roasted coffee. This suggested that OTA was masked by reactions with the substrate during roasting. The absence of OTA in green coffee is therefore the best guarantee of safety.     

Synthesis of unsaturated polyesters of increased solubility in styrene

The present study presents the synthesis of unsaturated polyester resins using only one glycol i.e., ethylene glycol. Polyesters of inorganic solubility in styrene were prepared. Properties of the resins in the noncrosslinked state in the process of crosslinking and after curing were studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3143–3150, 2006     

应用SPC技术对机械零件加工过程的管理和控制

介绍了SPC(统计过程控制)技术原理，以某传动轴外径φ45 0.50^0.90 mm为控制对象，提出应用SPC技术，对机械零件加工过程进行管理和控制，从而达到过程失控预警、过程不断改进、过程能力不断提高的目的，继而保证产品质量的稳定和不断提高。     

3-D MCM封装技术及其应用

介绍了超大规模集成电路（VLSI）用的3-D MCM封装技术的最新发展，重点介绍了3-D MCM封装垂直互连工艺，分析了3-D MCM封装技术的硅效率、复杂程度、热处理、互连密度、系统功率与速度等问题，并对3-D MCM封装的应用作了简要说明。     

单微乳液中制备Ag/TS-1及丙烯气相环氧化

采用N2H4还原含AgNO3的单微乳液制备了Ag／TS-1催化剂。TEM表征结果表明，Ag高度分散于TS-1之上。以H2、O2存在下的丙烯气相环氧化为探针反应，考察了Ag／TS-1的催化性能。结果表明，采用Ag／TS-1为催化剂，Ag的负载量为1％（质量分数，下同），823 K焙烧后，373 K下反应30 min时，丙烯转化率为1．69％，环氧丙烷（Propylene oxide，PO）选择性为93．2％。当Ag的负载量超过2％时，反应过程中生成大量的热，造成PO的选择性下降。采用Ag的负载量为8％的Ag／TS-1催化剂，消除热效应后，丙烯的转化率为2．46％．PO的选择性为79．2％。     

Results of a User Study on 2D Hurricane Visualization

We present the results from a user study looking at the ability of observers to mentally integrate wind direction and magnitude over a vector field. The data set chosen for the study is an MM5 (PSU/NCAR Mesoscale Model) simulation of Hurricane Lili over the Gulf of Mexico as it approaches the southeastern United States. Nine observers participated in the study. This study investigates the effect of layering on the observer's ability to determine the magnitude and direction of a vector field. We found a tendency for observers to underestimate the magnitude of the vectors and a counter‐clockwise bias when determining the average direction of a vector field. We completed an additional study with two observers to try to uncover the source of the counter‐clockwise bias. These results have direct implications to atmospheric scientists, but may also be able to be applied to other fields that use 2D vector fields.