熔融温度对PP中成核剂的异相成核作用的影响

用DSC研究了熔融温度对不同类型成核剂成核PP的异相成核作用的稳定性的影响。观察到随熔融温度提高，纯PP的成核作用稳定，降温结晶温度基本不变。而有机磷酸盐类成核剂成核PP的结果温度比纯PP的高，而且异相成核作用受熔融温度的影响也很小。但山梨醇类成核剂成核PP的异相成核作用随熔融温度提高，结晶温度逐步降低明显，表明其异相成核作用对热不稳定。     

高压热处理对氧沉淀低温形核的影响

研究了外加高压(1GPa)下对450℃热处理硅片中氧沉淀行为的影响.透射电镜观察表明相对于大气压下热处理的样品,高压处理的样品会产生密度更高、尺寸更小的氧沉淀,表明高压有利于小直径氧沉淀的生成.电学性能测试表明,高压下处理的样品其热施主生成浓度和生成速率远远高于常压下处理的样品,这表明热施主与低温热处理过程中生成的高浓度氧沉淀核心有密切的关系.     

Development of High Thermal Conductivity Aluminum Nitride Ceramic

AIN ceramics with densities varying from 3.18 to 3.30 g/cm³ and room-temperature thermal conductivities varying from 88 to 193 W/m K were produced. Different sintering conditions, packing powders, AIN powder sources, carbon additive, and sintering times were evaluated, and the key processing parameters which cause the differences in density and thermal conductivity were identified. SEM, TEM, and EDS were used to characterize the correlation between thermal conductivity, microstructure, and processing parameters. The important parameters which control the thermal conductivity of AIN ceramics are discussed.     

大型钢制焊接双层低温储罐设计建造

介绍了大型钢制焊接双层低温储罐的结构形式、选材、建造、检验及保冷要求 ,结合所设计的低温液氨储罐 ,对设计建造这类储罐必须考虑的一些问题作了分析     

金属PTC陶瓷复合材料结构及其导电机理

研究了金属ＰＴＣ陶瓷复合材料的电学性能和其材料组分。结果表明，掺入金属的ＰＴＣ陶瓷材料经氮气中烧结，然后在空气中进行热处理，材料表面形成高势垒层，金属ＰＴＣ陶瓷复合材料的室温电阻较ＰＴＣ的陶瓷高。样品之中存在大量不同类型的极化，在低温时样品电阻较高，温度增加后，大量各种类型离子极化出现，在变价金属铁的变价导电作用下，削弱表面势垒，使金属ＰＴＣ陶瓷复合材料电阻降低，表现出ＮＴＣ现象。在电场作用下，正负电荷、晶粒畸变和空位缺陷等产生空间电荷极化使金属ＰＴＣ陶瓷复合材料有较高介电常数。介电损耗（ｔｇδ）频谱和介电δ温度谱上都出现一个介电峰，其主要原因是跃迁极化，金属阳离子由一个位置跃迁到另一个位置，在介电损耗所对应的频率和温度时出现跃迁极化率最大     

脉冲功率器件直流和动态热特性探测

介绍了针对影响微波脉冲功率器件可靠性的热性能问题，应用红外热分析技术。对比探测微波脉冲功率器件在动态和直流状态下的温度分布，峰值结温，热阻及其变化规律。     

Properties of ligno‐cellulose fiber Hildegardia

Studies on some properties such as the density, the degradation temperatures, the morphology and the spectral features of the ligno‐cellulose fiber Hildegardia were carried out in both untreated and alkali treated form. The fibers are found to have good morphology and moderate initial and final degradation temperatures. On alkali treatment, the lignin was found to be eliminated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2216–2221, 2002     

Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

Effect of heating-rate on failure temperature of pre-loaded brass H62

The response and failure of brass H62 specimens subjected to different levels of pre-loaded stresses and heating rates were investigated using a Gleeble-1500 thermal-mechanical material testing system. The metallographs of the tested material were also observed and analyzed. It is found that the increase of either pre-loaded stress or heating-rate decreases the failure temperature. Metallographic analysis shows that high heating-rate may cause stronger local thermal inconsistency （LTI） and remarkably increase the microdefects in the material, which may markedly degrade the macroscopic mechanical properties of the material.     

用离子束混合及快速热处理方法形成钽的硅化物

本文描述用离子束透过钽金属膜进行混合和快速热处理方法来形成钽的硅化物.用溅射方法在P型硅衬底上淀积一层金属钽,然后用砷离子束透过钽金属模进行混合,采用快速热处理后形成了平整的硅化钽薄层.使用厚度为500埃的钽金属膜,得到钽的硅化物薄层电阻为5.5Ω/□.研究了砷离子能量、剂量及钽膜厚度对钽的硅化物薄层电阻的影响.用透射电镜和台阶仪对所形成的硅化钽进行了分析和厚度测量.