Determination of polymer–polymer interaction parameters using inverse gas chromatography

A modified method is discussed that is based on Farooque and Deshpande's method to obtain polymer–polymer interaction parameters using inverse gas chromatography (IGC) data. In the Farooque and Deshpande method, the ratio of the difference of probe–polymer interaction parameters between two polymers and the probe volume [(χ₁₂ ? χ₁₃)/V₁] is used as the abscissa. In the modified method, the ratio [(?₂χ₁₂ + ?₃χ₁₃)/V₁] is used as the abscissa. Experimental data previously reported for a poly(?‐caprolactone)‐polyepichlorohydrin (PCL/PECH) blend and a poly(ethyl acrylate)‐poly(vinyl propionate) (PEA/PVPr) blend are analyzed. It is found that the slopes obtained by the new method had smaller deviations from the theoretical values than the Farooque and Deshpande method. The standard deviations of both slopes and intercepts obtained from the new method are also smaller. Using the new method, the polymer–polymer interaction parameters obtained from the intercept are negative numbers for the PCL/PECH system and very small positive numbers for PEA/PVPr. Explanations are given for the probe and concentration dependency of the polymer–polymer interaction parameters that are generally observed in IGC studies. A new method for selecting the best probe for calculating the interaction parameter is discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 671–680, 2003     

高坝洲电站碾压混凝土纵向围堰拆除爆破设计与实践

介绍了高坝洲电站碾压混凝土下游纵向围堰现场爆破试验成果,在分析爆破试验效果的基础上进行碾压混凝土围堰拆除爆破设计,详细分析了拆除爆破实施效果及主要影响因素.     

基于人文关怀的信号配时方法研究

在传统的信号配时中，都是以减少车辆的总延误为目标，这样并不能很好地体现出整个社会中人的时间价值。现以减少所有通过交叉口的出行者的总延误为目标，在传统的信号配时方案的基础上，提出了一套新的配时方案，同时以减少全部出行者的总延误时间为目标给出了相应的延误评价公式，最后以杭州市文一路-古翠路口的实测交通数据进行分析，论证了本配时方案的有效性。     

一种简单的S参数去嵌入技术

介绍了在低成本夹具上，任意微带结构二端口网络S参数去嵌入的方法；该方法用于获取放大器模块的S参数，根据这些参数设计的C波段的放大器实测结果与仿真一致。     

Free energy simulations of the HyHEL-10/HEL antibody-antigen complex

Free energy simulations are reported for the N31^L-D mutation,both in the HyHEL-10-HEL antibody-lysozyme complex and in theunliganded antibody, using the thermo-dynamic-cycle perturbationmethod. The present study suggests that the mutation would changethe free energy of binding of the complex by –5.6 kcal/mol(unrestrained free energy simulations), by –0.5 kcal/mol(free energy simulations with a restrained backbone) and by1.8 kcal/ mol (Poisson-Boltzmann calculations, which also usea restrained geometry model). A detailed structural analysishelps in estimating the contributions from various residuesand regions of the system. Enhanced recognition of HEL by themutant HyHEL-10 would arise from the combination of thermodynamicallymore favorable conformational changes of the CDR loops uponassociation and subsequent charge pairing with Lys96 in theantigen.     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

聚电解质溶液分子热力学模型

<正>链状聚电解质由于是长链大分子又有很高的电荷密度,其溶液即使在极低的浓度下仍具有很强的负偏差,与Debye-Huckel理论预测的结果相去甚远。工程上使用的Manning模型认为聚离子的电荷密度有一临界值,当超过临界值时,反离子即凝聚在聚离子表面使其实际电荷密度降至临界值。Nagvekar等在该模型的基础上引入NRTL方程,以计及短程相互作用的贡献。Manning等的方法虽然有一定的物理意义,但临界值的确定缺乏可靠的根据。     

旋波媒质基本参数的一种测试方法

本文提出了直接利用旋波材料板的Ｓ参数获得其基本参数的方法。通过自由空间测量旋波材料板的反射场和透射场，可以反演得到媒质的复介电常数、复磁导率、旋波量以及透射场的轴比和旋转角，测试程序简单，结果精度高。