Psychological impact of colorectal cancer screening.

This article examines the psychological impact of participating in sigmoidoscopy screening for colorectal cancer prevention. The 1st study examined psychological well-being at 3 months, in relation to screening outcome, in 4,153 individuals. The 2nd study used longitudinal data to examine changes in psychological functioning from before to after screening in relation both to screening outcome and baseline indicators of vulnerability. There were few psychological differences between those who had received negative results or had polyps detected. These findings were confirmed in the longitudinal study, which also found no evidence for vulnerability to adverse effects among those who were initially most anxious or who perceived their risk of cancer to be higher. The longitudinal data suggested that screening might produce transient positive effects. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

煤基链篦机-回转窑一步法直接还原设备改造及技术操作要点

本文主要论述了煤基链篦机-回转窑一步法直接还原关键设备改造及有关技术操作要点，并提出了进一步提高产量，稳定操作，延长作业周期，降低生产成本的技术改造方案。     

唐钢ER70S-6焊丝钢的生产工艺研究及质量分析

介绍了唐钢ER70S-6焊丝钢的特点，对盘条质量进行了分析。对该钢化学成分、冶炼和轧制工艺进行了优化研究，使其综合性能明显改善。     

无铬钝化技术研究的进展

评述了文献报道和各种不同的无铬钝化工艺的特点及其发展现状。目前还没有一种无铬钝化工艺能够完全代替铬酸盐钝化工艺，某些无铬钝化工艺在某些方面已经与铬酸盐钝化相当，但其市场前景、应用范围及用户环保效果还需要进一步研究。     

Micromechanical modelling of ductile crack growth in the binder phase of WC–Co

This study focuses on numerical simulation of ductile failure in the Co binder phase of WC–Co hardmetal. The growth of edge cracks under mode I loading is considered. A computational micromechanics approach is taken where the Co binder ligaments are explicitly represented in finite element models. An embedding technique is employed. Crystal plasticity theory is used to represent plastic deformation in the Co ligaments. Crack propagation in the binder is simulated using an element removal technique based on a modified Rice and Tracey model for ductile void growth, and fracture resistance curves are generated. Parameter studies are performed for variations in microstructrual parameters such as numbers of Co ligaments ahead of the crack tip and local Co volume fraction. The importance of thermal residual stresses and finite element mesh density are also investigated.     

First Harmonic (2f) Characterisation of Resonant Frequency and Q-Factor of Micromechanical Transducers

In this paper, the response to the first harmonic component (2f) of the electrostatic force in single terminal driven electrostatic comb-drive and parallel-plate drive was used as a signal to extract device parameters, namely, the Q-factor and resonant frequency instead of the fundamental (1f) resonance response. It is shown that the difficulty in motional measurement due to electrical cross-talk (parasitics) using 1f measurement can be overcome with a higher signal-to-noise ratio of the 2f signal. Both atmospheric (low-Q) and reduced pressure environment were investigated using off-chip electronics and lock-in amplifier. The measurements were done on the electrostatic comb-drive and capacitive parallel plate sensing plates that form the two core modules of a yaw rate sensor (dual-axis resonator). The effects of AC and DC bias voltages on the measured response have been investigated. Experimental amplitude and phase response data have been analysed using the Lorentzian curve-fit, Resonance Curve Area (RCA) method, the half-power bandwidth method (3 dB) and the Nyquist plot for data fitting and determination of the Q-factor and resonance frequency.     

云南东川泥石流沟与非泥石流沟~(137)Cs示踪法物源研究

运用1 37Cs示踪法调查云南东川小江流域 6条泥石流沟、6条非泥石流沟和主河的泥沙来源。泥沙主要来源于冲沟侵蚀和滑坡崩塌堆积、坡耕地和草地。坡耕地和草地表层土壤1 37Cs平均含量分别为 0 9Bq m2 和1 98Bq m2 ,冲沟沟壁和滑坡崩塌堆积土体1 37Cs。作者通过 3种源地土体1 37Cs含量的比较 ,分析了细粒泥沙(<0 0 1mm)的来源。 6条泥石流沟冲沟侵蚀和重力侵蚀 (滑坡崩塌 )的相对产沙量变化于 90 2 %～ 1 0 0 % ,平均值为 95 1 % ,6条非泥石流沟的相对产沙量变化于 74 5 %～ 83 3% ,平均值为 78 9%。小江主河为 81 4 %。     

计算机技术在电子装备测试系统中的应用研究

在现代测试技术快速发展的今天，计算机已成为武器装备自动测试系统中不可缺少的重要组成部分。高性能的计算机软件技术更是构建智能型、集成化自动测试系统的关键所在。分析了先进的软件技术在自动测试系统中的应用状况；并以导弹地面测量雷达系统为例，具体介绍了利用系统仿真方法进行装备自动检测的技术实现。     

微区电阻测试方法及新测试仪研制

文章对国内外开展微区薄层电阻测试的方法进行了综述，特别对改进范德堡四探针技术方法的测试原理、测试过程与测试结果进行了论述与分析，对微区电阻测试方法的进一步发展提出了一种可操作的方法，并研制出新型四探针测试样机。     

超声处理对RTM成型复合材料界面性能的影响

在RTM成型过程中采用超声技术。探讨了超声处理的最佳工艺参数,着重研究超声处理对RTM成型复合材料界面性能的影响。结果表明,在RTM成型过程中采用超声技术增加了树脂对纤维增强体的浸润性,使树脂中的空气和成型过程中产生的气泡易于排出,从而减少了复合材料的孔隙率,进而改善复合材料的界面性能。