钛合金的银脆,镉脆敏感性及其控制

利用慢应变速率拉伸技术（ＳＳＲＴ），并结合恒载实验，较全面地研究了Ｔｉ－６Ａｌ－４Ｖ合金的银脆行为、固态与液态镉脆行为，确定了应变速率、接触条件、热处理制度、试样取向、温度等因素对Ｔｉ－６Ａｌ－４Ｖ合金银脆与镉脆敏感性的影响，探讨了Ｎｉ阻挡层对控制Ｔｉ－６Ａｌ－４Ｖ合金和ＴＣ１１合金银脆开裂的作用。     

精对苯二甲酸反应器桨叶断裂分析与修复

为了保证进口精对苯二甲酸装置氧化反应器中钛制搅拌器的正常工作，对钛制搅拌器桨叶在运行中断裂脱落的原因进行了分析，并叙述了桨叶修理的方法和要求。经修理后的桨叶投入生产使用，达到了预期的目标。     

Kinetics study of Ti[O(CH2)4OCHCH2]4 initiated ring‐opening polymerization of ε‐caprolactone by differential scanning calorimetry

Chemical shrinkage was used for the in situ measurement of the progressing chemical stabilization reactions and the influence of ozone during the stabilization of polyacrylonitrile. A method for evaluating the activation energy through the sensitivity temperature is presented. The calculated results show that the activation energies were 161.57 kJ/mol in air and 181.23 kJ/mol in ozone-enriched air. Therefore, the chemical reactions were postponed during stabilization in ozone-enriched air. Ozone seemed to act in three ways: first, ozone promoted the formation of the serious skin–core structure. Second, ozone accelerated the chemical reactions and shortened the stabilization time at lower heating rates. Third, ozone postponed the chemical reactions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

纳米掺钼二氧化钛光催化剂研究发展

介绍了纳米掺钼二氧化钛光催化剂的制备、特性及应用     

电渣20Mn1A钢中铝和钛的控制

总结了电渣 2 0Mn1A钢从电炉冶炼到电渣重熔钢中铝、钛及主要成分的变化情况 ,为该钢的生产提供了控制成分的依据     

漫谈钛合金在舰船上的应用

钛合金优良的耐海水腐蚀性能、高的比强度、无磁性等特点,使其在船用领域大有潜力可为,我国的船用钛合金经过近40年的研究开发,基本能满足舰艇不同强度级别的需求,在舰船上应用具有明显的社会效益和经济效益,值得进一步应用推广。本文介绍了国内外舰船用钛合金的开发及应用情况。对钛合金在鱼雷发射水缸、高压气瓶、一回路危急冷却器、声扫雷具、二回路泵、阀及管系、声纳导流罩、螺旋桨等方面的应用作了重点介绍。     

LASER CLADDED TiCN COATINGS ON THE SURFACE OF TTTANIUM

Laser cladded coatings of TiCN were produced on the surface of titanium. To obtain the optimal techniques, several conditions were tested by varying the laser scanning rate. The choice of shielding gas was also studied. The cladded coatings were then evaluated from the surface mechanics point of view based on their microhardness. The microstructure of some interesting samples was investigated by optical micrographs （OM）. The results showed that under the condition of fixed pulse frequency and pulse width, the laser scanning rate and the shielding gas are the main factors influencing the components of coatings. TiCN coatings were decompounded and oxidized during the cladding process in the condition of no shielding gas of N2. X-ray diffraction results indicated that the composite coatings composed of TiCN, TiC, Ti2N, and TiO2 were produced using appropriate techniques. The results indicated that the best condition in terms of the surface microhardness is obtained when the scanning rate is 1.5mm/s, the pulse frequency is 15Hz, the pulse width is 3.0ms, and N2 is chosen as the shielding gas. The microhardness of the composite coatings is about 1331kg · mm^-2, which is about 4 times that of the substrate. The optical micrographs indicated that the cladding zone is made up of TiCN, TiO2 and some interdendritic Ti, but the diffusion zone mainly consists of the dendrites phase, and the cladded depth is about 80μm, which is more than 2 times that of the laser nitrided sample. There were no microcracks or air bubbles in the cladded sample, which was cladded using the above optimal techniques.     

连续运转的掺钛蓝宝石激光器

本文报导一种连续波氩离子激光泵浦的掺钛蓝宝石激光器。在氩离子激光功率(全谱线)为10.45瓦且仅用一组腔镜时,获得最大平均功率超过1000mW、调谐范围750～850nm的掺钛蓝宝石激光输出。     

不同品位高钛渣对沸腾氯化工艺的影响

分别以94％品位高钛渣和90％品位高钛渣为原料，采用沸腾氯化工艺制备粗TiCl4，分析了两种品位高钛渣对沸腾氯化工艺的影响。结果表明：94％品位高钛渣由于其活性低而对沸腾氯化工艺的影响较大。     

Contact interaction of double titanium and chromium diboride with Fe-Cr alloys

The kinetics of wetting double titanium and chromium diboride by iron-based alloys with different chromium content is studied. It is shown that contact angles are formed in such systems over the range 0–10°. The energy parameters of wetting are calculated. It is established that chromium as a surface-active element promotes Fe-Cr alloy spreading on the diboride surface. The microstructure of the interaction area is studied. It is shown that terminal solid solutions and eutectics are formed in the TiCrB₂-(Fe-Cr) system. The optimum compositions of the metallic binder are determined for TiCrB₂-based composite materials. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 1–2(453), pp. 109–115, 2007