网带式连续烧结炉炉温及网带速度微机控制系统

本文介绍一个基于ＳＴＤ总线的单片机网带式连续烧结炉炉温及网带速度控制系统，详细叙述了系统的硬件结构和控制算法。     

T8钢—聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性，磨料磨损性及土壤的减粘降组性能，与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％－－２２．２７％。     

Charge transfer resistance of spray deposited and compressed counter electrodes for dye-sensitized nanoparticle solar cells on plastic substrates

Electrochemical impedance spectroscopy was used to determine the effective charge transfer resistances of porous dye-sensitized solar cell counter electrodes prepared by low-temperature spray deposition and compression of conductive carbon and platinized Sb-doped SnO₂ powders on indium tin oxide-coated plastic substrates. The charge transfer resistances were 0.5–2 and 8–13 Ω cm², respectively, when using 3-methoxypropionitrile as the electrolyte solvent. The manufacturing method used lends itself to produce mechanically stable and even-quality electrodes in an easy and fast manner.     

Promising alloys for intermediate-temperature solid oxide fuel cell interconnect application

The formation of a low Cr-volatility and electrically conductive oxide outer layer atop an inner chromia layer via thermal oxidation is highly desirable for preventing chromium evaporation from solid oxide fuel cell (SOFC) metallic interconnects at the SOFC operation temperatures. In this paper, a number of ferritic Fe–22Cr alloys with different levels of Mn and Ti as well as a Ni-based alloy Haynes 242 were cyclically oxidized in air at 800 °C for twenty 100-h cycles. No oxide scale spallation was observed during thermal cycling for any of these alloys. A mixed Mn₂O₃/TiO₂ surface layer and/or a (Mn, Cr)₃O₄ spinel outer layer atop a Cr₂O₃ inner layer was formed for the Fe–22Cr series alloys, while an NiO outer layer with a Cr₂O₃ inner layer was developed for Haynes 242 after cyclic oxidation. For the Fe–22Cr series alloys, the effects of Mn and Ti contents as well as alloy purity on the oxidation resistance and scale area specific resistance were evaluated. The performance of the ferritic alloys was compared with that of Haynes 242. The mismatch in thermal expansion coefficient between the different layers in the oxide scale was identified as a potential concern for these otherwise promising alloys.     

Studies on the corrosion behavior of cerium-implanted zircaloy-4 with GAXRD

In order to study the influence of cerium ion implantation on the aqueous corrosion behavior of zircaloy-4, specimens were implanted by cerium ions with a fluence range from 1×10¹⁶ to 1×10¹⁷ ions/cm² at maximum 150°C, using MEVVA source at an extracted voltage of 40 kV. The valence and elements penetration distribution of the surface layer were analyzed by X-ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES) respectively. Glancing angle X-ray diffraction (GAXRD) was employed to examine the phase transformation due to the cerium ion implantation in the oxide films. Three-sweep potentiodynamic polarization measurement was employed to value the aqueous corrosion resistance of zircaloy-4 in a 1 N H₂SO₄ solution. It was found that a significant improvement in the aqueous corrosion behavior of zircaloy-4 implanted with cerium ions compared with that of the as-received zircaloy-4. The improvement effect will declined with raising the implantation fluence. The bigger is the fluence, the less is the improvement. Finally, the mechanism of the corrosion behavior of the cerium-implanted zircaloy-4 is discussed.     

硬粒子对聚合物材料表面的冲击摩擦研究

冲击摩擦为接触面切向与法向冲量之比。用聚合物材料试件与弹簧钢片组成振动测试系统 ,硬粒子以一定入射角冲击试件水平面引起系统振动 ,接触冲量通过振幅反映出来 ,记录初始振幅值而计算出一个冲击过程的冲击摩擦因数。结果表明 ,当入射角α在 2 5°-60°变化时 ,冲击摩擦因数f从 0 .5降至 0 .2左右。文章同时分析讨论了摩擦对聚合物表面接触强度的影响。     

1,4,5,8-四氮杂氢化萘（2,3,-6,7）并双呋咱衍生物的合成

由1，4，5，8—四氮杂氢化萘(2，3，-6，7)并双呋咱经羟甲基化、酰化、硝化和叠氮化等反应合成出一系列热稳定的呋咱含能衍生物，并以^1HNMR、IR、MS、元素分析鉴定了其结构。     

考虑加筋切向阻力的土坡稳定分析

目前在加筋边坡的极限平衡稳定分析中,认为加筋中产生的预应力能约束土体的运动或者能使抵抗土体运动的阻力增加,而对于加筋的切向阻力作用却没有考虑。主要讨论了在加筋土坡稳定分析时,加筋的切向阻力在加筋工程中起到的作用。认为在加筋边坡的极限平衡稳定分析中,也应考虑加筋的切向阻力作用;提出了计算公式,编制了相应的程序,给出了算例。     

高硬度耐磨电弧喷涂管状丝材的研究

利用自熔性合金与非晶态材料的特点，研制了Fe—B系管状丝材作为电弧喷涂材料，其形成的涂层具有良好的结合强度、低的孔隙率、高的硬度和耐磨损性能。     

分压式电阻测量的闭环负反馈方法

提出一种反馈分压式电阻测量方法，给出了两种改进方案，分析了它们的测量误差，指出了减小误差的途径和方法。