Preliminary investigation for the production of wet-process phosphoric acid from Saudi phosphate ores

This paper represents the first published report of a preliminary investigation of the possibility of using Saudi phosphate ores for the production of wet-process phosphoric acid.     

微晶纤维素增粘剂的研制

以棉浆为原料，废盐酸为水解催化剂，所得合成革用微晶纤锥素增粘剂的质量指标达到了德国和日本同类产品的标准。     

Synthesis, characterization, and catalytic properties of polysiloxanes with pendant 4-(3-pyridinyl)butyl and 4-(1-oxypyridin-3-yl)butyl groups

New silane monomers with the pendant 4-(3-pyridine)butyl group have been synthesized by hydrosilation of 3-(3-butenyl)pyridine with Me _n Si(OEt)_3-n H (n=0, 1) using a platinum catalyst. Only -addition products were observed. The products were characterized by elemental analysis, infrared,¹H- and¹³C-NMR spectroscopy, and gas chromatography-mass spectrometry. Hydrolysis-polycondensation of the difunctional monomer with a basic catalyst, Me₄NOH, gave a mixture of cyclic oligomers, principally cyclic tetramer, and linear homopolymer. Under similar reaction conditions, the trifunctional monomer gave crosslinked material which was soluble in common organic solvents. The linear homopolymer and crosslinked polymer were trimethylsilyl end-blocked with hexamethyldisilazane. The cyclic and end-blocked polymers were characterized by elemental analysis and spectroscopic methods. Molecular weights of the polymers were obtained by end-group analysis using¹H-NMR spectral data, size exclusion chromatography, and direct insertion-probe mass spectrometry. The cyclic, linear, and crosslinked materials were N-oxidized withm-chloroperoxybenzoic acid and characterized by spectroscopic methods. The polymeric N-oxide derivatives were shown to be effective transacylation catalysts in the synthesis of mixed carboxylic acid anhydrides in immiscible solvents (H₂O/CH₂Cl₂) under phase-transfer conditions. The implications of the results on the mechanism of catalysis are discussed.     

弱酸性条件起始合成MUF树脂工艺研究

为了开发一种新的在"弱酸—弱碱—弱酸—弱碱"条件下合成三聚氰胺-尿素-甲醛树脂(MUF)的工艺,对弱酸性条件下起始合成MUF工艺进行研究.探讨了在不同酸性阶段加入的三聚氰胺对脲醛树脂性能的影响,找出最佳的三聚氰胺改性脲醛树脂的合成工艺.在最佳工艺基础上,评价三聚氰胺用量对MUF树脂性能的影响以及对胶合板性能的影响,并对MUF树脂和普通脲醛树脂进行红外分析.结果证明:三聚氰胺在甲醛与尿素一次缩聚之后加入,对脲醛树脂改性效果最好,其胶合板湿剪切强度与甲醛释放量之间达到较好平衡,胶合板甲醛释放量为0.63mg/L,湿剪切强度为1.03MPa.红外谱图分析表明:三聚氰胺分子以亚甲基与脲醛树脂分子链相连并有可能嵌入脲醛树脂分子链中,形成一定数量的醚键,使三聚氰胺在脲醛树脂中真正起到骨架作用.     

强化两相混合的超临界技术制备聚乳酸微粒

针对商品化聚乳酸微球粒径分布较宽难于适用气溶胶给药要求的不足,采用水力空化混合强化超临界流体辅助雾化技术(SAA-HCM)制备聚乳酸(PLA)超细微粒.该技术主要特点是通过在超临界流体和液相进料处引入水力空化混合器,强化两相间的混合.考察SAA-HCM过程混合器压力、温度、沉淀器温度、进料中CO2与液体溶液质量流量比和溶液质量浓度等操作参数对微粒形态和粒径分布的影响,成功制备出球形度较好,粒径分布较窄(1～3μm)的PLA微球.经X射线衍射(XRD)分析和差示扫描量热(DSC)分析显示,与原料PLA相比,微球晶型及热曲线变化不大,但结晶度下降.同时把操作参数与相行为进行关联,探讨了影响颗粒形貌的机理.对比超临界流体辅助雾化法(SAA)的实验结果表明:水力空化的引入能有效强化混合器内的两相传质,混合更好,能制备出适用于气溶胶给药要求的超细微粒.     

双三羟甲基丙烷丙烯酸酯的合成研究

采用酰氯法合成双三羟甲基丙烷丙烯酸酯．实验考察了原料配比、反应温度以及阻聚剂的用量等因素对产品酯化率的影响,确定了适宜的反应条件．酯化反应的酯化率最高可达89％．生成的产物为浅黄色黏稠状液体．产物经红外光谱、质谱定性分析,确定为目的产物．     

From surface science to catalysis: Surface “explosions” observed on Rh crystals and supported catalysts

Phenomena called surface explosions have been reported for decomposition reactions on single crystals, and have been identified by the use of desorption methods. In particular, in TPD, they are manifested by extremely narrow peaks (as little as 3 K in width) and a desorption rate which increases with time in isothermal experiments. In this paper we report such observations for acetate species on Rh single crystals, but extend this to show for the first time that such effects are not restricted to single crystal/UHV experiments, but can also be found on a Rh/Al₂O₃ catalyst under ambient pressure conditions. These reactions can be classified as second order autocatalytic surface processes, where free surface Rh sites are an essential component of the reaction. It is shown that coadsorbed adatoms are also essential for such explosions to be seen and their role is proposed to be that of a template layer acting to order the acetate in self-poisoning configurations.     

Change in the molecular weight distribution of poly(ethylene oxide) caused by the complexation with poly(acrylic acid)

The complexation between poly(ethylene oxide) (PEO) and poly(acrylic acid) (PAA) was made by using double the molar quantity of either polymer component at pH 2 where the resulting complex completely precipitates. After the removal of the precipitate, PEO or PAA remaining in the supernatant was subjected to gel permeation chromatography to investigate the change in the molecular weight distribution (MWD) caused by the complexation. No remarkable difference is observed in the MWD curves for PEO[1] (M_w=1.37 × 10⁴) before and after the complexation with PAA[1] (M_w=1.10 × 10³) and PAA[2] (M_w=4.16 × 10⁵). However, the MWD curves of PEO[2] (M_w=1.26 × 10⁵) and PAA[2] become shortened and shift to the low molecular weight side after the complexation with PAA[1] or [2] and PEO[2], respectively. This tendency is enhanced by increasing the complexation temperature. From these results, it is indicated that the complexation between PEO and PAA deals with an equilibrium reaction, and the equilibrium constant is dependent on the chain length of both polymer components and also on the complexation temperature.     

In situ esterification of rice bran oil with methanol and ethanol

In situ esterifications of high-acidity rice bran oil with methanol and ethanol and with sulfuric acid as catalyst were investigated. In the esterification with methanol, all free fatty acids (FFA) dissolved in methanol were interesterified within 15 min, and it was possible to obtain nearly pure methyl esters. The amount of methyl esters obtained from a given rice bran was dependent on the FFA content of the rice bran oil. In the esterification with ethanol, it was not possible to obtain pure esters as in methanol esterification, because the solubilities of oil components in ethanol were much higher than those in methanol.     

XRQ-Ⅱ型开车燃烧控制系统的结构及应用

XRQ-Ⅱ型开车燃烧控制系统由泵组、阀组、燃烧器、快速关断阀门及控制柜等组成,燃料经油枪喷嘴雾化喷出在燃烧器中安全稳定地燃烧,控制柜保证供油及点火、火焰检测.在600 kt/a硫磺制酸系统焚硫炉烘炉及催化剂升温中的实际应用表明,XRQ-Ⅱ型开车燃烧控制系统具有便于自控操作、提高焚硫炉烘炉内衬质量、缩短催化剂升温时间等优点.