Cellulose acetate reverse osmosis membranes: Optimization of the composition

Membranes based on cellulose acetate for reverse osmosis can possibly be applied to the so‐called salinity process of energy generation and water desalinization. The requirements for membranes for these two different applications are a relatively high water flux and low salt permeability. In this article, we present the optimization of the composition of such membranes. We started by producing membranes with a patented casting solution with the following composition: 45.77 wt % dioxane, 17.61 wt % acetone, and 8.45 wt % acetic acid (solvents); 14.09 wt % methanol (nonsolvent); and 7.04 wt % cellulose diacetate and 7.04 wt % cellulose triacetate. The membranes produced with this solution were analyzed comparatively, with the membranes obtained by the introduction of modifications to the following parameters: the solvent mix, the nonsolvent mix, the proportion of cellulose diacetate and cellulose triacetate in the casting solution, and the addition of reinforcing cellulose fibers. The results led us to conclude that the best membrane formulation had the following composition: 45.77 wt % dioxane, 17.61 wt % acetone, and 8.45 wt % acetic acid (solvents); 4.22 wt % cellulose triacetate and 9.86 wt % cellulose diacetate (polymers); 14.09 wt % methanol (nonsolvent); and 0.5 wt % cellulose fibers (with respect to the total polymer content). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4052–4058, 2006     

Color and COD retention by nanofiltration membranes

In the present study the application of the nanofiltration process was investigated mainly in the retention ofcolor and chemical oxygen demand (COD) present in textile industry wastewater. Nanofiltration experiments were carried out in a pilot unit, operating in crossflow. Three different types of spiral wound membranes, DK 1073, NF 45 and MPS 31 were used simultaneously in the same unit. The results of the tests showed that for color retention, the values were around 99% for the DK 1073 and NF 45 membranes and the 87% for COD retention for the DK 1073. The permeate flux for the different wastewaters varied from 30.5 to 70 L/h.m². Fouling was observed in all membranes due to the accumulation of molecular species close to the filtering surface. The process was efficient and promising for the reuse of wastewater from this type of industry.     

添加剂对PSF/ER合金膜结构和性能的影响

介绍了大分子添加荆聚乙烯吡咯烷酮(PVP)和小分子添加荆H2O时聚砜(PSF)／环氧树脂(ER)合金膜结构和渗透、分离及成膜性能的影响。结果表明，添加荆使PSF／ER合金膜的水通量上升，截留率下降；PVP改善了PSF／ER合金膜的成膜性能，当水质量分数大于0．8％时，PSF／ER合金膜的成膜性能下降。     

A genetic tango attack against the David–Prasad RFID ultra‐lightweight authentication protocol

Radio frequency identification (RFID) is a powerful technology that enables wireless information storage and control in an economical way. These properties have generated a wide range of applications in different areas. Due to economic and technological constrains, RFID devices are seriously limited, having small or even tiny computational capabilities. This issue is particularly challenging from the security point of view. Security protocols in RFID environments have to deal with strong computational limitations, and classical protocols cannot be used in this context. There have been several attempts to overcome these limitations in the form of new lightweight security protocols designed to be used in very constrained (sometimes called ultra‐lightweight) RFID environments. One of these proposals is the David–Prasad ultra‐lightweight authentication protocol. This protocol was successfully attacked using a cryptanalysis technique named Tango attack. The capacity of the attack depends on a set of boolean approximations. In this paper, we present an enhanced version of the Tango attack, named Genetic Tango attack, that uses Genetic Programming to design those approximations, easing the generation of automatic cryptanalysis and improving its power compared to a manually designed attack. Experimental results are given to illustrate the effectiveness of this new attack.     

Controlled pore size, thickness and surface free energy of super-hydrophobic PVDF® and Hyflon®AD membranes

Super-hydrophobic membranes were manufactured by using two per-fluorinated polymers such as PVDF and Hyflon AD. The combination of controlled structure and supra-molecular chemistry made these membranes ideal interfaces to be used in membrane contactors.     

Pervaporation of 50 wt % ethanol–water mixtures with poly(1‐trimethylsilyl‐1‐propyne) membranes at high temperatures

Poly(1‐trimethylsilyl‐1‐propyne) (PTMSP) membranes have been used to separate ethanol–water mixtures by pervaporation. This polyacetylene is known to present high affinity toward ethanol, showing high selectivity and ethanol permeation flux. The performance of this polymer in the separation of alcohol–water solutions has been evaluated over long periods (572 h) at a high temperature (75°C) to examine the deterioration of the transport properties in the separation of 50 wt % ethanol–water solutions. Although PTMSP membranes present good characteristics for the separation of gases and liquid mixtures, their organic selectivity decrease with the operating time because of the relaxation processes of the polymeric chains, which affect the free volume of the polymer, the deterioration being more evident for concentrated solutions. The effects of the operation temperature on the characteristic parameters of pervaporation have also been studied to establish how this variable affects the performance of PTMSP membranes. The selectivity increases slightly with the operation temperature, but the effect of the temperature on the separation factor decreases as membranes are degraded with the operation time. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2843–2848, 2007     

女性护理液抗炎止痒作用的实验研究

女性护理液为中药苦参醇提液加三氯羟基二苯醚复配而成，根据药理方法学以实验动物建立模型，观察护理液的抗炎、止痒作用。结果，单独使用三氯羟基二苯醚，有较好的抗菌消炎作用，但是止痒作用不明显。以苦参醇提液和三氯羟基二苯醚复配，其抗炎、止痒作用均接近地塞米松磷酸钠注射液。     

Surface morphology and nodule formation mechanism of cellulose acetate membranes by atomic force microscopy

By the use of atomic force microscopy (AFM), formation mechanism of nodular structure in cellulose acetate membranes was systematically investigated. Elementary factors affecting the nodule formation were delineated on the basis of both kinetic and thermodynamic considerations. It was shown that (1) the exact nature of nodular structure is thermodynamic equilibrium glassy state; nodular structure will vanish in the rubbery state; (2) the thermodynamic factor affecting nodule formation is the membrane formation temperature; with the membrane formation temperature decreasing, more chain segments are able to form nodular structures; (3) nodule formation is dependent on the segment rearrangement; variation of the solvent environment is the major kinetic factor affecting the segment rearrangement and nodule formation. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1328–1335, 2003     

一种基于边界特征线且特征点可变的二阶非线性离散跟踪微分器及在测速定位系统中的应用

利用状态反推方法确定最速离散二阶系统的线性区域的边界特征线及控制特征线,以相平面上的点及边界曲线、控制线的相对位置按线性规则确定控制量的大小,区分可达区与线性区,并依此构造最速分段线性函数形式的跟踪微分器（Tracking-differentiator,TD）,这种算法可以方便地修改特征点,适应能力强,而且运算中不包含任何根号运算,使得控制综合函数的形式极大简化,有利于工程实现.对正弦信号及方波信号的仿真结果表明了上述结论的合理性.验证了特征点分段线性算法在适当修改特征点后得到的TD,与经典TD以及它的线性近似进行比较,跟踪能力和微分提取能力都得到了较大的提高.应用移动平均算法构成的跟踪微分器组,具有相位补偿功能,适当选取TD参数后,得到了滤波能力强、相位特性良好的滤波器,并应用于基于长定子齿槽检测的永磁电动磁悬浮列车的测速定位系统中.实验结果表明,本文提出的简化TD按相位补偿确定的方案能有效滤除脉冲和扰动等噪声,对过轨道接缝时的畸变信号进行修复,边界容易修改,算法简单有效,实时性强,易于工程实现.     

Microporous anisotropic phase inversion membranes from bisphenol A polycarbonate: Effect of additives to the polymer solution

Phase inversion is a very flexible technique to obtain membranes with a large sort of morphologies. Membrane properties can vary greatly depending on the kind of polymer system used. Bisphenol A polycarbonate (PC) could be used as a phase inversion membrane base polymer, and presents very good properties. Nevertheless, very little information on membrane preparation using PC and the phase inversion process can be found in the literature. In this work flat‐sheet microporous membranes were obtained by the phase inversion process using the immersion precipitation technique. A new polymer system was studied, consisting of polycarbonate, N‐methyl‐2‐pyrrolidone as solvent, water as the nonsolvent, and an additive. The influence of some parameters on membrane morphology, such as polymer solution composition, exposition time before immersion into the precipitation bath, and the kind of additive was investigated. Precipitation was followed using light transmission experiments and membrane morphology was observed through Scanning Electron Microscopy (SEM). The viscosity and cloud points of all polymer solutions were also determined. The results were related to the studied synthesis parameters, using the basic principles of membrane formation by the phase inversion technique, looking forward to establishing criteria to control the morphology of flat‐sheet membranes using polycarbonate as the base polymer. The results showed that both additives were able to increase pore interconnectivity and even suppress macrovoid formation. The decrease in the miscibility region of the polymer system and increase in mass transfer resistance are found to be the determining factors during polymer solution precipitation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3085–3096, 2002