不等厚板过渡削薄对接焊缝的超声波探伤

不等厚板经过渡削薄处理后的对接焊缝,由于厚度的不均匀,射线穿透时的衰减不一样,对射线检测带来很大的麻烦。常用的超声波探伤方法在定位和定级方面比较困难,本文给出利用现在先进的数字式超声波探伤仪进行准确探伤的方法。     

血液过滤用熔喷PBT非织造布紫外辐照接枝改性研究

研究了血液过滤用熔喷PBT非织造布的紫外辐照气相接枝改性方法。通过实验选择了丙烯酸(AAc)为接枝单体 ,探讨光照时间、预辐照时间、单体温度、引发剂浓度、氮气压力对接枝率和表面润湿张力的影响 ,结果得到最佳的紫外辐照接枝条件为 :室温下 ,光距 2 0cm ,预浸 10min ,二苯甲酮 (BP) 0 .0 37mol/L ,冲入单体的氮气流量 87.5h/L ,反应时间 30min。PBT非织造布AAc紫外辐照接枝后表面润湿张力可以达到 85mN/m左右 ,且表面润湿张力随接枝率的提高而增加     

原位聚合法研制纳米胶囊相变材料

采用超声波工艺及细乳液原位聚合方法,研制了以聚苯乙烯为囊壁、正十八烷为囊芯的纳米胶囊相变材料;系统探讨了聚合反应各因素如引发剂、链转移剂、表面活性剂以及正十八烷/苯乙烯比等对乳胶粒子的形态、胶囊材料热性能的影响,对所研制的胶囊相变材料进行激光衍射粒度分析、透射电镜及差示扫描量热等表征.实验结果表明,在引发剂AIBN 0.5%(油相质量百分比,下同);链转移荆DD在T0.4%;复合乳化剂(SDS/OP10)总量2%,配比1:1及正十八烷/苯乙烯比=1:1条件下,胶囊呈球形均匀分布,聚苯乙烯囊壁能将正十八烷囊芯很好包裹住,其胶囊Z均直径124nm,相变焓可达124.4kJ·kg-1.     

超声提取-高效液相色谱法测定烟草中烟碱含量

确定了制备烟碱分析样品的超声波提取条件:0.4% NaOH溶液为溶剂,液固比40:1(mL·g-1),提取时间4 h.确定了高效液相色谱法检测烟碱含量的条件为Kromasil C18色谱柱(250 mm×4.6 mm,5 μm),检测波长259 nm,检测温度35 ℃,流动相CH3OH/0.02 mol·L-1磷酸盐缓冲溶液(V/V)为60/40,流速1.0 mL·min-1,进样量10 μL.平均加样回收率98.8%,相对标准偏差1.2%.结果表明超声提取-高效液相色谱法是一种准确度高,速度快的测定烟草中烟碱含量的检测方法.     

超声波对沉淀二氧化硅的分散解聚研究

研究了超声波对沉淀二氧化硅的分散解聚效果，实验证明，当频率为40kHz，功率密度达到1．8W/cm^2时，沉淀二氧化硅浆料可以获得极佳的分解效果，二氧化硅聚集体小于77．6nm的颗粒数量达98．9％。     

自控温加热带的研制

研究了炭黑含量、辐照剂量以及体系共结晶性对以高密度聚乙烯/乙烯 丙烯酸乙烯酯共聚物为基材的自控温加热带电阻率及电热稳定性能的影响,以及加工条件和后处理工艺对材料电性能的影响。结果表明,50～80kGy的辐照剂量为本体系提供优异的电热稳定性,适当的加工及后处理工艺能大大改善该体系的导电性。     

Dis-Bond Detection and the Possibility of Interfacial Stiffness Measurement with Real-Time Impulsive Stimulated Thermal Scattering

We describe a new, real-time, noninvasive method for dis-bond (delamination) detection which is based on a technique known as impulsive stimulated thermal scattering (ISTS). We first explain the ISTS technique and compare data from polyimide films tightly bound to silicon substrates with data from unsupported polyimide films. The observed differences in the data from these two cases are readily understandable and offer an unmistakable signature for delaminations. We demonstrate ISTS dis-bond detection by locating and mapping out randomly-distributed and spatially-fine regions of delamination in a polyimide film-silicon substrate system. Finally, we present two simple physical models of the interfacial region which comprehensively describe acoustic data from the tightly-bound and the unsupported samples. With insight from simulations using these models, we suggest how ISTS might be used to determine interfacial adhesion quality and we show how ISTS sensitivity to interfacial effects can be adjusted.     

超声辐照制备SrFeO3降解苯酚光催化性能研究

采用超声辐照柠檬酸络合法制备了复合氧化物SrFeO3，以苯酚为光催化探针分子，以450W高压汞灯为光源（主波长〉410nm），研究了SrFeO3光催化性能、研究表明，经过超声辐照制备的SrFeO3光催化活性提高一倍以上。XRD、TEM、DRS表征结果表明，超声辐照制备的SrFeO3粒径均匀、分散性好、粒径较小，光吸收红移显著。探讨了超声提高催化性能的机理。     

Potential of microbial growth control in water hydraulic systems by UV‐irradiation and filtration

Water hydraulic systems use water as a pressure medium and, thus, do not pose such adverse environmental impacts as oil hydraulics. Microbial deterioration of the pressure medium and biofouling of the surfaces restrict the applicability of the water‐based technology. The potential of microbial growth control by UV‐irradiation and filtration was studied in a pilot‐scale water hydraulic system. The UV‐irradiation (25 m Ws cm^?2) of the pressure medium reduced the total viable counts of bacteria by 1–2 log₁₀ cfu cm^?3, whereas the total microbial cell numbers and the numbers of surface‐attached microorganisms remained unaffected. Prefiltration (1.2 µm, absolute) of the pressure medium decreased the total microbial cell number in the water phase and retarded the attachment of bacteria. The filtration during the operation (2 µm, absolute) decreased the total numbers of microbial cells and the total viable counts in the pressure medium, and microbial attachment on the surfaces. Microbial attachment was not prevented by filtration. The microbial water quality obtained by pre‐ and on‐line filtration of the pressure medium was sufficient to ensure the long‐term operation of the water hydraulic system assuming that clean work practices are complied with in assembly and during the operation. © 2002 Society of Chemical Industry     

超声挤出DP/纳米SiO2复合材料的拉伸与流变性能

在高能超声波作用下,将纳米SiO2和一种新颖的共聚聚丙烯(DP)熔融共混,制备纳米复合材料,研究了纳米SiO2含量和超声波对复合材料拉伸和流变性能,以及脆断面形貌的影响。结果表明,低含量(≤2%)纳米SiO2对DP有增强作用,随着填料含量增加断裂强度下降。超声波的引入能提高含量较高SiO2(>2%)的复合材料的断裂强度和断裂伸长率,降低体系黏度,并有助于纳米SiO2在DP基体中均匀分散。