横向光泵获得S_2紫外激光

用ＸｅＣｌ准分于激光器（３０８．１ｎｍ）横向泵浦Ｓ２激光器，又成功地实现了Ｓ２Ｂ－Ｘ态近ＵＶ波段的激光振荡。在波长３３０．９～３９０．０ｎｍ范围内观测到６条近ＵＶ激光输出。测量了有关的激光参数。     

堆底熔穿事故的场外后果及其对策

在压水堆核电站应急计划和应急响应中，堆底熔穿事故占有重要位置。本文用法国核电厂事故源项Ｓ３（对应于堆底熔穿事故）计算了在典型气象条件下的场外放射学的后果，根据一般防护决策原则和我国颁布的干预水平，提出了保护公众的应急防护措施的建议。     

轴向柱塞泵配流副油膜的实验研究

本文介绍了对６３ＣＹ１４－ＩＢ型轴向柱塞泵配流副油膜的实验研究结果。该研究结果为改进该泵配流副的性能提供了依据。     

森兰变频器在循环水供水系统中的应用

介绍森兰变频器在循环水供水系统中的应用,实现了能耗的节约以及故障的自动切换。     

乳化液泵站变频调速系统的设计

针对传统的乳化液泵站调速系统存在机械损耗比较大的问题,提出了一种乳化液泵站变频调速系统的设计方案;给出了该系统的硬件结构,详细介绍了该系统的工作模式及软件设计。实际应用表明,该系统运行稳定、机械损耗小。     

Soft computing approach to fault diagnosis of centrifugal pump

Fault detection and isolation in rotating machinery is very important from an industrial viewpoint as it can help in maintenance activities and significantly reduce the down-time of the machine, resulting in major cost savings. Traditional methods have been found to be not very accurate. Soft computing based methods are now being increasingly employed for the purpose. The proposed method is based on a genetic programming technique which is known as gene expression programming (GEP). GEP is somewhat a new member of the genetic programming family. The main objective of this paper is to compare the classification accuracy of the proposed evolutionary computing based method with other pattern classification approaches such as support vector machine (SVM), Wavelet-GEP, and proximal support vector machine (PSVM). For this purpose, six states viz., normal, bearing fault, impeller fault, seal fault, impeller and bearing fault together, cavitation are simulated on centrifugal pump. Decision tree algorithm is used to select the features. The results obtained using GEP is compared with the performance of Wavelet-GEP, support vector machine (SVM) and proximal support vector machine (PSVM) based classifiers. It is observed that both GEP and SVM equally outperform the other two classifiers (PSVM and Wavelet-GEP) considered in the present study.     

Continuous electromagnetic separation of inclusion from aluminum melt using alternating current

A novel scheme about the continuous electromagnetic purification of aluminum melt was put forward based on the utilization of a square separation pipe and a 50 Hz alternating current to produce electromagnetic force. It is experimentally found that with electrical current of 400 A/cm^2, it takes only 10 s to remove 95% inclusion from aluminum melt. Comprehensive numerical simulations were carried out to investigate the dynamics mechanisms behind the process. The results show that the removal of inclusion is attributed to the cooperative effects of electromagnetic buoyancy and the secondary flow induced by the rotational electromagnetic force, and the removal efficient increases with the size of inclusion and the electrical current imposed. Theoretical predictions on the distribution and removal efficiency of inclusion were supported by the experiments.     

不可逆量子斯特林热泵循环性能分析与优化

建立了以一维无限深势阱中极端相对论粒子为工质的不可逆量子斯特林热泵循环模型。考虑高低温热源之间的热漏,导出了循环的性能系数与无量纲泵热率的表达式。分析了循环性能与各性能参数之间的关系。研究发现,热泵的性能系数与无量纲泵热率都随粒子在状态1进处于激收态上的占有几度单调递减,性能系数与无量纲泵热率都是势阱宽度比的凸单调函数。无量纲泵热率关于性能系数的关系曲线为回原点的扭叶型,并确定了该不可逆量子斯特林热泵的最优运行区间。     

高温精炼处理对铸造镍基高温合金组织与性能的影响

研究了高温精炼处理对铸造镍基高温合金组织与性能的影响.普通铸造镍基合金枝晶组织粗大,晶界碳化物呈链状分布,晶内碳化物呈草体汉字状密集分布于枝晶间,是合金塑性低的主要原因.经高温精炼处理后,合金的枝晶组织细化,晶界及枝晶间的碳化物数量减少,γ γ共晶相数量增加,晶界碳化物呈不连续质点状分布,晶内碳化物的密集程度下降,拉伸塑性和蠕变(持久)寿命得以明显提高.经1 650℃,5 min高温熔体处理后,合金室温延伸率由3.5%提高到9.2%,700℃高温塑性由2.0%提高到8.0%,900℃高温塑性由2.8%提高到9.6%,蠕变寿命由34 h提高到52 h,蠕变塑性由4.3%提高到6.11%.推荐的最佳高温精炼处理制度为1 650℃保温4 h.分析了高温精炼处理对合金液态结构、凝固组织与性能的影响机理.     

不锈钢水泵底架成形工艺及模具设计

分析了水泵底架原冲压成形工艺存在的问题,提出了新的成形工艺方案,介绍了新工艺中关键工序的模具结构以及模具加工、现场调试应注意的事项。经生产验证,改进后的工艺与模具结构合理,产品质量及生产效率大大提高。