热固型甲基丙烯酸酯真空浸渗剂发展概况

本文简述了真空浸渗剂的发展概况，着重介绍了其中的热固化浸渗剂及其组成和浸渗工艺。     

提高太安堆积密度的结晶工艺研究

以季戊四醇经浓硝酸酯化后的粗制太安为原料，在溶课题上重结晶得精制成品太安，讨论了不同溶剂，结晶速度，结晶溶液pH值对太安堆积密度的影响。     

Studies on crystallization behaviors and crystal morphology of polyamide 66/clay nanocomposites

X‐ray diffraction methods, DSC thermal analysis, and polarized light microscopy (PLM) were used to investigate the structural changes of nylon 66/clay nanocomposites. PA 66/clay nanocomposites were prepared by the method of melt intercalation. The results indicate that the addition of the intercalated organo‐montmorillonite (OMMT) can induce generation of the β‐form crystal of PA 66 and substantially affect the arrangement of molecules in the α‐form crystal, although the crystallinity scarcely changes. Also, the DSC results indicate that the addition of OMMT in the PA 66 matrix leads to increases of crystallization temperatures and the full width at half maximum (FWHM) of the exothermic peaks. Moreover, the viscosity factor is the main influence on FWHM of the exothermic peaks of PA 66/clay nanocomposites. The results of nonisothermal crystallization kinetics show that OMMT has the effect of heterogeneous nucleation and leads to the decrease of the size of the spherocrystal. The heterogeneous nucleation effects of OMMTs influence the mechanism of crystallization and the growth mode of PA 66 crystals. PLM photographs verify that the size of spherocrystal is decreased and visually confirm the theory of crystallization kinetics. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 756–763, 2005     

湿法磷酸生产装置衬胶防腐技术及胶板的选用

介绍衬胶防腐在湿法磷酸生产中的应用 ,特别是真空设备设计衬胶防腐的要点以及目前我国湿法磷酸装置中国产 (含合资、独资企业 )胶板的特点和选用、施工中应注意的事项。     

真空系统的工艺设计

介绍真空系统的基本概念、工艺设计及实际应用。     

Solid‐state polymerization of poly(ethylene terephthalate). I. Experimental study of the reaction kinetics and properties

The solid‐state polymerization (SSP) reaction kinetics of poly(ethylene terephthalate) were investigated in connection with the initial precursor intrinsic viscosity (IV; molecular weight). Evaluations were performed with otherwise equivalent precursors melt‐polymerized to IVs of 0.50, 0.56, and 0.64 dL/g. The changes in the molecular weight and other properties were monitored as functions of the reaction times at solid‐state temperatures of 160–230°C. Precursors with higher initial molecular weights exhibited higher rates of SSP than those with lower initial values, as discussed in connection with the levels of crystallinity and the carboxyl and hydroxyl end‐group composition. Activation energies decreased at temperatures above 200°C, and this indicated a change in the SSP reaction mechanism. At temperatures of 200–230°C, similar activation energies were required for the polymerization of all three precursors. Lower temperature polymerizations, from 160 to 200°C, required higher activation energies for all precursors, with the 0.50‐IV material requirement almost twice as high as that calculated for the higher IV precursors. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 197–212, 2003     

提高发酵过程乙醇分离效率的新型反应器

设计了一种新型的带侧臂循环的气升式反应器,该反应器可以有效地把真空闪蒸发酵和汽提发酵2项技术结合起来。实验结果表明,与单独的汽提和闪蒸过程相比,利用此反应器进行同步汽提闪蒸操作,大大提高了乙醇的移出效率,从而进一步提高了发酵强度。     

冰箱门胆真空吸塑成型模具抽芯机构设计

在充分分析斜滑块抽芯机构运动及受力状态的基础上，介绍了一种利用脱模力抽芯的非气动抽芯机构设计方法，采用该方法设计的冰箱门胆吸塑模具结构紧凑、抽芯可靠、生产效率高。     

麝香体系结晶分离研究

研究了根据酮麝香、1,3-二甲基-2,4-二硝基-5-叔丁基苯晶体生长速度的不同,从对二者均达到饱和的溶液中分离得到1,3-二甲基-2,4-二硝基-5-叔丁基苯晶体的过程,计算了晶体生长速度并进行了实验验证。     

真空间歇精馏分离橙花醇和香叶醇的研究

橙花醇和香叶醇是重要的基础香料,沸点差仅为2℃,具有热敏性。以往研究中应用减压间歇精馏分离橙花醇和香叶醇的混合物,一次精馏得到90%以上的产品收率低(仅为46%),且塔釜温度较高,操作周期长,不宜于工业生产。本文针对沸点差较小的热敏性物系,采用减压高效间歇精馏方法对橙花醇和香叶醇的混合物进行了分离研究。通过考察全回流时间、回流比、加热负荷和压力等操作因素对分离效果的影响,确定了适宜的操作条件,塔顶压力为600Pa～700Pa,塔压降为4800Pa～4900Pa,釜温在150℃～152℃之间,全回流6h,采用20 1,10 1,5 1的变回流比操作。实验结果显示,单塔精馏即可得到含量大于90%的橙花醇和香叶醇,收率在65%以上,提高20%无热分解现象,过程稳定,为工业生产奠定了基础。