双组分高固体丙烯酸聚氨酯涂料的研究

介绍了改性高固体分羟基丙烯酸树脂的合成工艺，通过对引发剂、链转移剂、反应温度及叔碳酸缩水时油酯等因素的讨论，合成了新型的羟基丙烯酸树脂。以其为基料配制了丙烯酸聚氨酯涂料，并讨论了该磁漆的配方设计和各项性能。     

含三嗪环的酸酐固化剂合成及其环氧固化物性能研究

将桐油(TO)经过三(2-羟乙基)异氰尿酸酯(THEIC)改性处理后再引入顺丁烯二酸酐(MA),得到新型含有三嗪环的酸酐固化剂(TTA)。通过红外光谱分析确定了其结构,用TGA分析结果表明,其与E44环氧树脂的固化物耐热指数达到174.5℃,在空气气氛中的热老化性能优于用THEIC和双马来酰亚胺改性的桐油酸酐固化剂的环氧固化物。     

高性能环氧树脂涂料的研制

以甲基丙烯酸、丙烯酸丁酯及苯乙烯的聚合为接枝体，在过氧化苯甲酰作用下对E-51环氧树脂进行接枝改性，同时对三乙烯四胺进行曼尼希改性，制得多种改性固化剂，并用其与改性的环氧树脂配制成涂料，实验结果表明，当苯酚、甲醛和三乙烯四胺的物质的量比为3：3：1时固化剂的固化性能最好。     

耐高温绝缘涂层的研制

采用有机硅树脂、无机粘结剂和无机填料制备的有机无机复合耐高温绝缘漆，其涂层经600℃，1h的热处理后可具有良好的附着力和绝缘性能。配套后的绝缘涂层，可在250℃下长期使用，并具有良好的耐冷热循环、耐湿热的能力。     

甲基丙烯酸缩水甘油酯的合成

在季铵盐催化作用下 ,甲基丙烯酸与环氧氯丙烷反应生成甲基丙烯酸缩水甘油酯。实验结果表明 ,二步法可获得较高的产率     

Microstructure and morphology of amine-cured epoxy coatings before and after outdoor exposures—An AFM study

Atomic force microscopy (AFM) has been used to study the morphology and microstructure of an amine-cured epoxy before and after outdoor exposure. Measurements were made from samples prepared in an essentially CO₂-free, H₂O-free glove box and from samples prepared in ambient conditions. For those prepared in a CO₂-free glove box, AFM imaging was conducted on (1) an unexposed air/coating surface, (2) an unexposed coating bulk, (3) an unexposed coating/substrate interface, and (4) a field exposed air/coating surface. For samples prepared in ambient conditions, only the unexposed air/coating surface was investigated. The same regions of the exposed samples were scanned periodically by the AFM to monitor changes in the surface morphology of the coating as UV exposure progressed. Small angle neutron scattering and Fourier transform infrared spectroscopy (FTIR) studies were performed to verify the microstructure and to follow chemical changes during outdoor exposure, respectively. The results have shown that amine blushing, which occurs only under ambient conditions, had a significant effect on the surface morphology and microstructure of the epoxy. The surface morphology of the samples prepared under CO₂-free, dry conditions was generally smooth and homogeneous. However, the interface and the bulk samples clearly revealed a two-phase structure consisting of bright nodular domains and dark interstitial regions, indicating an inhomogeneous microstructure. Such heterogeneous structure of the bulk was in good agreement with results obtained by small angle neutron scattering of unexposed samples and by AFM phase imaging of the degraded sample surface. The relationship between submicrometer physical changes and molecular chemical degradation is discussed. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004, in Chicago, IL.     

环氧-聚酰胺体系中增韧剂的研究

在环氧-聚酰胺体系中分别加入“海岛结构”QS-1、聚硫橡胶、液体丁腈橡胶增韧改性,通过对固化物剪切强度、弯曲弹性模量及断裂强度的对比,“海岛结构”QS-1增韧综合性能较好.     

Thermal Shock Failure in Thick Epoxy Coatings

In this paper we describe an apparatus for reproducibly measuring thermal shock resistance of thick polymer layers bonded to metals. The thermal shock behavior is discussed in terms of epoxy samples bonded to an aluminum substrate. It was found that both high resin toughness and low resin thermal expansion coefficient improved thermal shock resistance of thick coatings, but only a sample containing 60wt. % glass beads did not develop a failure crack. Effects of sample thickness, temperature gradient, and resin composition on thermal shock behavior are discussed.     

水性聚氨酯胶粘剂的研制

以低聚物多元醇、二异氰酸酯和二羟甲基丙酸为主要原料制备了一种阴离子水性聚氨酯胶粘剂。探讨了不同种类的多元醇和异氰酸酯对预聚体的合成和乳液性能的影响,实验中发现用三乙胺做中和剂时存在着一个临界浓度。选用多种助剂最后配制得到了综合性能优良的水性聚氨酯胶粘剂。     

Molybdenum Oxycarbide and Tungsten Oxycarbide Coatings on Silicon Carbide Fibers

The strength and toughness of fibrous composites depend on the interface properties which control the bonding between the fibers and matrices. One method of controlling the interface involves coating the fiber with an appropriate material. In a previous study, it was found that there is a definite advantage in using low coating temperatures to prevent fibers from degrading. We therefore were interested in a report that Mo₂C could be deposited from Mo(CO)₆ at temperatures as low as 300° to 475°C. Our studies indicated that the material was not Mo₂C, but an oxycarbide, which, with an analogous tungsten oxycarbide coating, was applied to SiC yarns. Both oxycarbides could be converted to the metals by heat-treating in N₂.