Mechanical performance of ceramic matrix composite I-beams

Experimental studies have been performed on ceramic matrix composite (CMC) I-sections, which typify joint designs for CMC components. Axial loads and moments have been applied to activate delamination mechanisms. The maximum load bearing capacity has large variability, governed by the severity of manufacturing flaws located in the transition region of the I-section. This variability leads to an unsatisfactory design situation. Delaminations that form from these flaws arrest and behave in a stable manner, subject to a remanent load bearing capacity. This remanent capacity has minimal variability. Hence, design based on the remanent load would be robust. An expression for this design criterion is presented.     

一种新的纸基微流开关及其活跃方法

提出了一种新的、基于声表面波的纸基微流开关。通过软光刻技术制作内含两个微孔的聚二甲基硅氧烷(PDMS)微架,其上固定经折叠、长度可变的纸通道。PDMS微架贴附于压电基片之上,并在待连接的两微通道之下方,折叠纸通道最低端离压电基片间距为2 mm。压电基片上采用微电子工艺光刻一对叉指换能器和反射栅。当足够强度的电信号加到叉指换能器对时,激发两相向声表面波,使得压电基片上微流体输运到折叠纸通道,改变其长度,连接其上待连通的两纸基微通道,完成开关功能。对可编程微流器件提供了一种新的编程和开关控制方法。     

黄河淤积粉土的两种复合稳定方案与性能对比

为探索路基工程中黄河淤积粉土的稳定技术和性能保障方案,针对德州齐河县境内的黄河淤积粉土,在乳化沥青复合稳定粉土(AE稳定土)的研究基础上,采用无机/有机复合材料制备出一种复合固化剂(FG固化剂),研究了AE稳定土和FG稳定土2种稳定方案下粉土的抗压强度性质、水稳定性和抗冻融能力;结合XRD、SEM表征技术,探讨了FG固化剂的稳定机理。研究认为,FG固化剂稳定土较AE稳定土有着更高的无侧限抗压强度、回弹模量和承载能力,水稳定性良好,在抗冻融能力上有着比AE稳定土更好的效果。XRD与SEM分析表明,FG固化剂提供了活性矿物质,其复合胶凝效应和填充增强保障了粉土的抗压强度,高分子物质起到粘结颗粒界面、填塞孔隙的作用,降低了内部孔隙率;两者造成土体的最大干密度变大;与AE稳定土的稳定机理不同。FG固化剂的使用为黄河粉土的稳定和工程应用提供了参考方法。     

Two new characteristic parameters for runoff computation

A method capable of estimating the hydrograph from a prescribed storm for a practical mild slope upstream catchment is proposed. This method makes use of two new characteristic parameters, andS, in conjunction with the kinematic wave equation to compute lateral inflows of the main stream of the catchment. The depth profile of overland flow at any instant within the catchment and hydrograph at any location can be easily found. Lag times for individual lateral inflows are then considered and are linearly combined to obtain the hydrograph at the outlet of the catchment or depth profile of the main stream at any instant. The validity of the excess rainfall-surface runoff linear relationship in this study has also been verified with Tatsunokuchiyama catchment, and it shows good results for this computed runoff.     

Study on diffusion welding SiCp/ZL101 with Cu interlayer

Through the vacuum diffusion welding SiCp/ZL101 aluminum with Cu interlayer,the effect of welding parame-ter and the thickness of Cu on the welded joint property was investigated,and the optimal welding parameters were putforward at the same time.The microstructure of joint was analyzed by means of optical-microscope,scanning electron mi-croscope in order to study the relationship between the macro-properties of joint and the microstructure.The results showthat diffusion welding with Cu interlayer could be used for welding aluminum matrix composites SiCp/ZL101 successfully.     

AN EXPERIMENTAL-NUMERICAL METHOD FOR MEASURING CRACK PROPAGATING VELOCITIES UNDER STRESS WAVE LOADING

An experimental-numerical method for measuring dynamic crack propagating velocities under stress wave loading is established in this paper. The experiments of the three-point bend specimen are done on the improved Hopkinson bar. Deflection of loading point, dynamic load and instantaneous crack length are measured, then crack propagating velocities are calculated. Experiments on 40Cr steel show that the results given by this method have a good agreement with that obtained by the resistance fracture gage method. Therefore this method is feasible for measuring crack propagating velocities under high loading rate and will have wide application.     

露天矿山深-浅耦合台阶爆破方法研究及应用

爆破大块率高一直是困扰国内外众多露天矿山的技术难题,银山矿露天采矿场由于采区地质条件复杂,爆破大块率高的现象尤为明显。为此,针对露天采矿场岩性复杂易产生大块的区域,基于岩石的物理力学性质,计算出千枚岩和斑岩爆破区域需增设的短孔孔位。为减少爆破大块的产生率,提出了中深孔爆破方法—深-浅耦合台阶爆破方法。在银山矿露天采矿场实施深-浅耦合台阶爆破方法后,爆破大块率得到有效控制并取得了显著的社会及经济效益。     

Adaptive model predictive inventory controller for multiproduct warehouse system

An inventory control system has been developed for a distribution system consisting of a single multiproduct warehouse serving a set of customers and purchasing products from multiple vendors. Purchase orders requesting multiple products are delivered to the warehouse in a process referred to as joint replenishment. The receipt of customer orders by the warehouse proceeds in order intervals and in order quantities that are subject to random fluctuations. The objective of warehouse operation is to minimize the total cost while maintaining inventory levels within the warehouse capacity by adjusting the purchase order intervals and quantities. An adaptive model predictive control algorithm is developed using a periodic square wave model to represent the material flows. The adaptive concept incorporates a stabilized minimum variance control-type input calculation coupled with input/output stream parameter predictions. The boundedness of the control output under the suggested algorithm is mathematically proven under the assumption that disturbances in the orders are bounded. The effectiveness of the scheme was demonstrated using simulations.     

三箱式纺丝技术生产PET/PA6复合纤维

介绍了采用三箱式纺丝技术生产PET/PA6复合纤维的设备及工艺。重点对纺丝箱体、纺丝温度控制进行了详细的讨论。     

二维坡面雨洪水动力模型研究

由降雨产生的坡面洪水运动过程复杂,其可靠模拟仍有待深入。该文建立了基于浅水方程的二维坡面雨洪动力过程模拟的动力波模型,选用单坡、三阶坡面和复杂起伏多变坡面的雨洪运动为数值算例,进行了数值检验并与忽略惯性项的扩散波模型进行了对比分析。结果表明:动力波模型可以较好地模拟洪水过程,在峰现时间,洪峰水位的捕捉和退水过程等方面都表现出优良的特性;而且动力波模型在复杂坡面雨洪过程计算的适应性方面表现更佳。而扩散波模型在计算精度和稳定性方面都相对要差。虽然扩散波模型在单坡面算例中的计算精度也较高,但因受忽略惯性项的影响,退水过程有明显偏离。