Ablation of ice-solids and wax-solids mixtures in turbulent axisymmetric water jets

The ablation rate of frozen mixtures of water or wax with finely divided solids subjected to a turbulent axisymmetric water jet was investigated both experimentally and theoretically. The range of the water jet Reynolds number was 8700–29300 and the jet temperature varied between 22 and 60°C. The solids used were very fine kaolinite clay, titanium oxide and aluminium powder. The type of solids and their concentration were found to affect the ablation rate of ice-solids and wax-solids mixtures. This is mainly due to changes in the physical properties of the melt layer of the water-solids or wax-solids mixtures which forms between the impinging jet and the frozen mixtures.     

利用翅片管束外表面降膜反应脱除烟气中SO2的实验研究

A new wet flue gas desulfurization method by reaction across the falling liquid film on the outside surface of axial finned-tube bundle and its principles of removal of SO₂ are presented in this paper.The effects of different styles of tube bundle,and the pitch of tubes,flue gas velocity,gas-liquid ratio and flue gas temperature on desulphurization efficiency and the moisture content of flue gas are studied.The experiment results show that desulphurization effect is better for flue gas at 65℃,4.0m·s^-1 against the tube bundle of 10 rows with relative pitch of staggered rows S₁/d=2.1,S₂/d=1.8.     

浅谈燃煤电站锅炉热风测量装置

燃煤电站锅炉的热二次风风量测量装置大多采用了传统的机翼式测量装置,其测量使用过程中暴露出了一些严重的不足——节流较大而导致风机出力加大,测量装置及引压管路积灰导致测量失准,影响了相关自动控制的投用和保护的可靠性。也因此,该不足在某种程度上产生了电能生产过程中安全、稳定、经济等方面的负面作用,需要进行深入分析和整改。     

铝合金6061在低硫酸浓度硬质氧化过程中氧化膜微观组织的演变

采用自制的阳极氧化试验装置和扫描电子显微镜分别对铝合金6061在硫酸浓度为1%、2%、3%、4%和5%H2SO4(W t.%)的氧化液中形成的硬质阳极氧化膜进行研究。结果表明:随着硫酸浓度的增大,氧化膜的显微硬度和表面粗糙度降低,氧化膜中的孔洞逐渐变大;与硫酸浓度为1%和2%相比,3%左右硫酸浓度的氧化液所得到的氧化膜的均匀程度较好,以3%左右硫酸浓度的氧化液对铝合金6061进行硬质氧化较为理想。     

矩阵法计算流水施工工期

简要分析了代数法、图上法在计算流水施工工期时存在的不足,提出了用矩阵法计算流水施工工期的方法．设计并分析了计算用表,说明了计算步骤,并用实例进行了验证．     

脉冲电子束系统沉积高温超导薄膜研究

高温超导薄膜生长是研究超导现象和超导器件的基础,一直是凝聚态物理研究的一个重要课题。各种各样的薄膜生长方法都被应用于高温超导薄膜的生长研究。采用一种崭新的薄膜沉积设备——脉冲电子束沉积系统(PED)成功制备出了NCCO、LSCO高温超导薄膜,并通过优化沉积参数,获得了具有良好表面形貌和超导转变特性的高温超导薄膜。     

三参量模型粘弹性圆柱体轴向流动中的动力特性

对悬臂粘弹性圆柱体轴向流动中的动力特性进行了研究,计算模型采用三参量模型,对特征方程进行了推导,给出了在质量比β(β=0.5)一定,改变无量纲延滞时间α和无量纲弹性系数比λ的情况下,悬臂三参量模型粘弹性圆柱体的前三阶模态无量纲复频率ω的实部及虚部与无量纲流速v之间的关系曲线图.研究结果表明:在无量纲弹性系数比λ和质量比β一定时,随着无量纲延滞时间α的增加,及在无量纲延滞时间α和质量比β一定时,随着无量纲弹性系数比λ的增加,第一阶模态发生单一模态颤振及再次稳定的无量纲临界流动速度都在减小.     

等离子体抛光对表面粗糙度的影响

为了得到超光滑表面且无表层损伤的光学元件,引入一种新型的超光滑表面加工技术——等离子体抛光.在新设计的等离子加工实验平台上进行了等离子体加工工艺实验,对氧气流量,放电功率大小,磁场大小几个参数对基片表面粗糙度的影响进行了实验研究,且优化了工艺参数.结果表明增加氧气流量,合理控制功率和磁场强度都会使等离子体抛光基片表面粗糙度减小.当氧气流量为50 sccm,功率为80 W,磁场强度为17 mT时,粗糙度达到最小值0.9 nm.     

Preparation of micro-patterned surfaces of Si-N-O films and their influence on adhesion behavior of endothelial cells

Microgrooves were prepared on Si(100) surface by photolithography and wet etching.Subsequently,Si-N-O films were deposited on the microgrooves by unbalanced magnetron sputtering(UBMS) and micro-patterned surfaces of Si-N-O films were obtained.The size of the micropatterns was measured by surface profilometer.The chemical composition of Si-N-O films were characterized by X-ray photoelectron spectrometry(XPS) and the wettability of the micropatterned surfaces was evaluated by contact angle measurement.The beh...