The effects of glycol methacrylate as a dehydrating agent on the dimensional changes of liver tissue

The dimensional changes of liver sections during the course of processing with glycol methacrylate (GMA) or with ethanol are described. Tissue processing with ethanol served as a control. During prolonged processing steps (24 h each), linear shrinkage of tissue specimens dehydrated with GMA at room temperature was 13.2%. Subsequent infiltration with GMA resulted in trivial swelling, and polymerization in slight shrinkage (2.3%). In comparison, processing with cold GMA resulted in shrinkage during dehydration (about 10.8%), a slight swelling in pure GMA, followed by shrinkage during polymerization (2.2%). Short routine processing schedules resulted in similar shrinkage/swelling patterns, although precise values differed slightly. In all experiments, ethanolic dehydration resulted in smaller dimensional tissue changes than did GMA dehydration. The dimensional changes of tissue sections during stretching on water, mounting and drying compensated for the major part of the shrinkage manifested during processing.     

以杂多酸为催化剂合成乙二醇-乙醚的研究

研究了杂多酸催化无水乙醇和环氧乙烷(EO)制备乙醇乙醚的醚化反应,考察了不同种类的杂多酸以及醚化反应工艺条件对反应活性和选择性的影响.结果表明,PW_(12)催化剂的反应活性高、反应温度低、选择性好,当用PW_(12)作催化剂,乙醇与环氧化乙烷之比为3.0(mol),反应温度45℃,反应时间1h时,转化率和选择性均超过97%.     

Cu－MnO_2同槽电解半工业试验研究

提出了Ｃｕ－ＭｎＯ＿２同槽电解的新工艺，在同一电解槽同时得到电铜和电解二氧化锰两种产品，该新工艺具有低电耗、低酸雾污染和低酸耗等优点．     

用φ20mm离心萃取器两步法制取高纯钇

本文研究了中钇富镧稀土的氧化物溶液在环烷酸中的萃取行为，测定了镧钇组成、温度变化与分离系数的关系；在Ｐ＿（５０７）体系中研究了ｐＨ值与分配比的关系；提出用环烷酸、Ｐ＿（５０７）两种萃取剂制备高纯钇的工艺流程。用８４台φ２０ｍｍ离心萃取器进行了一个月的台架试验，结果证明两种萃取剂有很好的互补性，在满足钇的纯度要求下有较高收率。离心萃取器具有易分相、体系存留量少、液流密闭性好等优点，它更适宜于粘度大、级数多、产品纯度要求高的体系。     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

Temperature and pressure effects on supercritical CO2 extraction of tomato seed oil

Tomato seed oil was extracted with supercritical carbon dioxide in a semibatch-flow extractor within the temperature range 313–343 K and the pressure range 10.8–24.5MPa. The extraction rates increased with pressure, but decreased with temperature increase because of the variation in solvent density and resultant differences in oil solubility. The fatty acid composition of the extracted oil was similar to that of soybean oil.     

扑炎痛的合成新法

以水杨酸和对硝基苯酚为原料,在三氯氧磷存在下进行酯化,然后催化加氢还原硝基,最后用乙酐进行二酰化制得扑炎痛,三步收率分别为80.8％、90.4％和88.5％。     

High-pressure dc sputtering of High-Tc BPSCCO thin films withTc(0) above 100 K

High-T _c Bi(Pb)-Sr-Ca-Cu-O thin films have been made on single-crystal MgO substrates using high-pressure dc sputtering technique. X-ray studies confirm the crystallinity and highly oriented structure withc-axis perpendicular to the substrate. By optimizing the annealing schedule the formation of the high-T _c phase is stabilized. The best film exhibited superconducting transition temperature with zero-resistance temperature,T _c(0), as high as 101 K. Temperature dependence ofJ _c indicates the presence of Josephson-type weak links.     

马来酸及其酐和衣康酸与PP熔体接枝反应机理的研究

以马来酸酐作对照，用热分析、流变、化学分析等方法，研究了马来酸和衣康酸在非隔氧条件下与ＰＰ熔体催化接枝反应的特点和规律，阐述了单体结构－单元反应相对速率－－接枝产物结构之间的关系，提出了３种接枝物的结构模型。     

桐油改性酚醛树脂的结构及固化过程的研究

通过桐油与苯酚在酸性催化剂存在下反应，然后再在碱性催化剂存在与甲醛反应制得了一种热固性桐油改性酚醛树脂。利用红外光谱，差示扫描量热法分析技术对改性树脂的结构及固化反应过程进行了研究。