MB8镁合金薄板的搅拌摩擦焊

针对我国航空航天工业常用的MB8镁合金。采用搅拌摩擦焊工艺进行焊接，对其焊缝的成形特点、组织特征和力学性能进行分析。结果表明，采用搅拌摩擦焊焊接镁合金效果良好。     

古洞口水利水电工程泄洪洞工作弧门安装工艺

介绍了古洞口工程泄洪洞工作弧门在特定地形下采用固定卷扬式启闭机和汽车吊配合闸室的预埋件进行闸门安装的施工工艺。对闸门的吊装、调整及焊接工艺的具体措施作了详细分析,解决了该工作弧门在洞内安装的关键施工技术问题。     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

美国国家公园申报准则及审议程序

本文所讲述的是美国国家公园服务中心在评估申请提案、制定审查方案过程中所应用的各种标准和准则 ,同时也列出了一些认识、保护未列入国家公园体系中其他重要资源的途径和方法。     

Solution of a multidimensional inverse radiation problem by means of mode reduction

The Karhunen–Loève Galerkin procedure is employed to solve an inverse radiation problem of determining the time‐varying strength of a heat source, which mimics flames in a furnace, from temperature measurements in three‐dimensional participating media where radiation and conduction occur simultaneously. The inverse radiation problem is solved through the minimization of a performance function, which is expressed by the sum of square residuals between calculated and observed temperature, using a conjugate gradient method. Through the Karhunen–Loève Galerkin procedure, one can represent the system dynamics with a minimum degree of freedom, and consequently the amount of computation required in the solution of the inverse problem is reduced drastically when the present technique is adopted. Copyright © 2004 John Wiley & Sons, Ltd.     

摩擦焊在钢制实心抽油杆修复中的应用

通过对焊接工艺及焊后热处理工艺优化，采用摩擦焊接技术对报废抽油杆中仍有使用寿命的杆头与杆体进行了拼接，获得了性能达标的抽油杆。从而提高了旧杆的修复率．降低了采油成本。该技术可在抽油杆修复及相关行业进行推广应用。     

植筋施工工艺

以某网球馆改造工程为例 ,就植筋技术的概念及所用材料进行了介绍 ,详细阐述了其施工工艺流程及措施 ,指出植筋技术具有工艺简单、操作方便、造价相对较低等优点     

铁素体球墨铸铁与20钢的闪光对焊

试验使用铁素体球墨铸铁和20钢的实心棒料进行了闪光对焊，通过改变次级电压4～8级，通电时间3～5s，观察其焊接接头组织的变化并测定其抗拉强度。结果表明，接头由三个区组成；当通电时间一定时，抗拉强度随次级电压的升高先减小后增大；当次级电压一定时，抗拉强度随通电时间的增加而增大。在次级电压为8级、通电时间为5s时，抗拉强度达最大值，为370．8MPa，是20钢母材的90.4％，是球墨铸铁母材的83.7％。     

A direct estimate of JIc from the load versus load-line displacement record

The purpose of this study is to examine the current standard fracture toughness test procedure to determine if there could be an easier method to get a J_Ic value from the test record. The current method for determining J_Ic involves a detailed computational and construction procedure. The objective in this study is to simplify the analysis for the determination of J_Ic. The results of this study show that the load and displacement record for a fracture toughness test can be used to directly estimate a J_Q value, a provisional value for fracture toughness, J_Ic. The J value taken at the maximum load point can be used along with an adjustment factor to estimate a J_Q value. This J_Q estimate is close to the one obtained from the construction procedure of ASTM Standard E 1820. When a unit‐sized specimen is tested, that is, a specimen with a width of 50 mm and a thickness of 25 mm the maximum load point provides a direct estimate of J_Q. Other sizes require a size adjustment factor, which is simply a square root relationship between the width of the test specimen and a unit width. The proposed new method of estimating J_Q is simple in concept and requires a minimum number of calculations. It appears to produce values of J_Q which are comparable to those obtained from the ASTM E1820 construction procedure and may produce less scatter.     

爆炸焊接——热轧双相不锈钢复合钢板研制

本文主要阐述了通过爆炸焊接和热轧的方法,研制成功可焊性良好的且具有较好强度、韧性与综合性能的双相耐应力腐蚀的不锈复合钢板。还将热轧与热处理的两种试验作了较全面的常规、特殊检验试验,结果完全达到使用要求。