斜井前置液加砂技术现场应用

中原油田斜井(井斜20°)水力压裂过程中易产生多裂缝和存在严重弯曲摩阻,常出现早期脱砂现象。油、气井压裂后初期产量高,但递减快,稳产时间短(100d),累积产量少。针对这些问题研究了前置液加砂技术,现场应用结果表明,前置液中加入粉砂能有效控制压裂液滤失,降低储层伤害,实现裂缝深穿透,而且粉砂能支撑微裂缝,提高压裂效果;前置液加中砂能有效降低裂缝弯曲摩阻,提高施工成功率。应用该技术,中原油田斜井压裂成功率由初期的50%提高到95%以上,有效率88%,有效期延长了50d以上,应用效果显著。     

SPC在变速器制造中的应用

这里首先建立了SPC系统的数学模型及数据处理模型，在此基础上完成了系统的功能结构设计以及事务处理过程设计，建立了关键工序与质量特性值的选取准则，继而完成了代码设计、数据库设计和故障诊断专家系统的设计：所形成的SPC软件系统达到了原设计指标要求。     

采用奇异值分解设计广义系统的最优滤波器

本文讨论广义离散随机线性系统的状态估计问题，通过矩阵奇值分解，本文给出了一种设计降阶最优滤波器的实用方法，该方法同时还得到了动态系统和量测系统的干扰噪声的估计。     

Production of phosphoric acid with low content of impurities

The present work is to study the possibility for controlled distribution of the impurities when they are decomposed by sulphuric acid to wet phosphoric acid and phosphogypsum, as well as generating technological conditions for production of clean wet phosphoric acid and its derivatives - phosphoric fertilizers, food phosphates and other phosphoric products.A coefficient of distribution D_A is introduced as a general criterion for elements dispersion. The study includes relationships between the weight ratio sulphuric acid/natural phosphate and D_A; the period of decomposition and D_A; the particle's size content of the natural phosphate and D_A. The obtained experimental data and relationships about the influence of the above discussed technological parameters on dispersion of more than 23 elements allow for control of that process in wet phosphoric acid and phosphogypsum by selecting specific technological conditions. Thus, depending on the requirements of acid's consumers and procedures for secondary processing of phosphogypsum to end-products, a selective decomposition of the natural phosphates to phosphoric acid and phosphogypsum can be carried out with content of the impurities in those products varying in narrow limits.     

锚索测力计有关应用问题的探讨

通过分析锚索测力计因受力状态不同而带来的系统误差,提出了测力计实测锚固力的修正方法及部分测力计传感器失效后延续锚固力测值的计算方法.     

超高吨位灌注桩静载试验中的预应力混凝土反力装置

在复兴大桥超高吨位灌注桩的静载试验,预应力混凝土反力装置替代了传统的钢梁反力系统。这套装置主要包括预应力锚桩、预应力承台与预应力反力梁。试验结果表明,直接获得超高吨位大直径嵌岩桩的极限承载力相当不易,而对这类问题预应力混凝土反力装置是值得考虑的。     

耦合模模型的峰峰值与有效值

介绍了峰峰值和有效值的偶合模方程,给出了峰峰值P矩阵和有效值P矩阵的表达式。利用峰峰值P矩阵和有效值P矩阵模拟了纵向耦合谐振结构以及阻抗元结构的声表面波滤波器的频响。对比两种P矩阵的模拟结果,说明了峰峰值耦合模方程和有效值耦合模方程分析频响的等效性。     

Synthesis, characterization and catalytic application for wet oxidation of phenol of iron-containing clays

High-surface-area pillared clays (PILC) were prepared from naturally occurring montmorillonites by exchanging interlayer ions to polyoxocations containing (i) aluminum (Al₁₃-PILC), (ii) iron adsorpted onto Al₁₃-PILC, and (iii) iron and aluminum located within the same complex (Fe_0.8Al_12.2-PILC). The obtained Fe_0.8Al_12.2-PILCs were characterized by DR–UV–vis and IR spectroscopy, XRD, ESR, scanning electron microscopy and low temperature N₂ adsorption measurements. Important factors affecting catalyst activity and phenol removal efficiencies have been studied, i.e. the effect of pH, temperature, catalyst concentration and stability of the catalyst.     

Kinetics of phenol oxidation in a trickle bed reactor over active carbon catalyst

The wet air oxidation of phenol over a commercial active carbon catalyst was studied in a trickle bed reactor (TBR) in the temperature and oxygen partial pressure ranges of 120–160 °C and 0.1–0.2 MPa, respectively. The performance of the active carbon was compared in terms of phenol and COD destruction. The weight change of active carbon due to reaction was also measured. Finally, oxic phenol adsorption isotherms were assessed in batch conditions at 25, 125 and 160 °C. In order to use the conversion data obtained from the TBR for a kinetic study, special care was taken to check the kinetic control in the TBR experiments. Several kinetic models including power law or Langmuir–Hinshelwood expressions were considered to describe the catalytic oxidation of phenol over active carbon. The simple power law model with first order dependence on both phenol and oxygen concentration predicted satisfactorily the experimental data not only over the entire range of operating conditions studied, but also outside its validity range. Copyright © 2005 Society of Chemical Industry     

激光器实用价值的评判

提出用于评价激光器产品实用价值的Q因子,它由激光器的亮度、脉冲宽度及价格确定。Q值大的激光器,开发及发展的潜力大。