现代电子工业Cpk评价中的特殊问题

现代电子工业生产具有许多新的特点，如果不针对具体情况，均采用传统工业生产中广泛使用的常规方法计算其工序能力指数，评价生产工艺水平，将可能导致错误的结论。总结了电子工业生产中工艺参数的典型特点，并讨论了工序能力指数的正确计算方法。     

Effects of diacrylate monomers on the bond strength of polymer concrete to wet substrates

The bond strengths of polymer concretes containing up to 15% (based on polymer resin) of diacrylate (DA) monomers were examined and compared with those without DA. A change occurring with the addition of DA monomers was an increase in the bond strength of polymer concrete to wet substrates. Zinc diacrylate (ZDA) and calcium diacrylate (CDA) were each used as an additive to monomers and resins [methyl methacrylate (MMA), polyester, and two kinds of epoxies]. The variables were amount of the DA monomers and surface conditions (wet or dry and smooth or rough). Bond strengths were measured by tension bond. ZDA was found to improve the bond strength of MMA and polyester, whereas CDA improved the bond strength of epoxies. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 991–1000, 2003     

An investigation into the effect of various chemical and physical treatments of a South African phosphogypsum to render it suitable as a set retarder for cement

The work describes various physical and chemical treatments to eliminate the deleterious effects of impurities in phosphogypsum on the delayed setting time and impaired strength development behaviour of cement to which it was added as a set regulator. The physical treatments included washing, milling, and ultrasonic treatment of the material, while the chemical treatments dealt with acidic and basic additions to the phosphogypsum during the washing stage. It was found that chemical treatment with a milk of lime solution, which is often recommended in literature, was ineffective in reducing set retardation. Treatment with ammonium hydroxide or sulphuric acid was more effective in this regard. Intergrinding phosphogypsum with slaked lime improved its effectiveness in reducing set retardation, but the use of unslaked lime was less effective and also resulted in marked reductions in compressive strengths. A combined treatment of wet milling phosphogypsum with a lime slurry in a ball mall was derived from these experiments and is recommended for full-scale plant applications.     

MRC分集接收的MQAM在Nakagami信道上的性能分析

Nakagami信道是一种适应性较强的信道模型，MQAM(M-ary quadrature amplitude modulation)是一种频谱利用率较高的调制方式。在存在多径影响的无线通信环境中，最大比合并(maximum ratio combining)方式的分集接收是克服衰落的有效方法。本文利用适用范围更广的Nakagami信道模型，在多径衰落的情况下对最大比合并分集接收的MQAM系统误符号率性能作了分析。仿真结果对分析实际信道下具体系统的性能具有一定的参考价值。     

复杂目标的近场散射特性分析

详细分析了目标散射随距离而变化的特征，根据散射特点的不同将目标的散射特性分为远场散射、准近场散射、近场散射等三种情况，并对三种情况下的描述的手段进行了讨论，提出在近场条件下，用反射功率比的概念直接对散射目标的特性进行描述。     

滚动式冷床在高钢级油管生产线中的应用

根据石油开采业对石油机械产品的需求 ,利用机械理论基础知识 ,通过实践设计 ,提出了对几何尺寸长的金属管类进行调质处理后的均匀冷却方法 ,以满足其性能要求。     

PMN-PT陶瓷中的氧缺位及其消除

研究了组成中Pb含量的变化对组成为Pbx(Mg1/3Nb2/3)0.65Ti0.35O3的铌镁酸铅-钛酸铅(PMN-PT)陶瓷压电性能的影响,发现化学计量比组成(x=1)的Pbx(Mg1/3Nb2/3)0.65Ti0.35O3陶瓷经常出现压电性能的大幅度退化现象,而A位适量缺Pb能稳定地获得高性能的Pbx(Mg1/3Nb2/3)0.65Ti0.35O3陶瓷。XPS元素价态分析的结果表明,化学计量比的Pbx(Mg1/3Nb2/3)0.65Ti0.35O3陶瓷中含有较多的氧缺位,氧缺位的产生源于MgNb2O6(MN)合成过程中的气氛差异,A位适量缺Pb能有效地消除这种氧缺位而稳定地获得正常的压电性能,其机理被认为是氧缺位与铅缺位的复合。     

The correlation of texture and magnetic properties in Co-Cr films

This investigation focuses on the correlation between the crystallographic orientation of grains with respect to magnetic properties in Co-Cr films. Based on a distribution measured for the (0002) crystallographic pole densities, modified formulae describing the texture were used to calculate the coercivity Hc, the squareness ratio Rs (Mr⊥/TMs) and the anisotropy field Ha for Co-Cr films. In general, calculated values for the coercive force He agreed well with the measured values. The calculated Rs⊥. values were much larger than the measured ones, however, indicating that the influence of the demagnetizing field and the magnetostriction on the orientation of the magnetization cannot be neglected. On leave from Institute of Computing Technology, Academia Sinica, P.O.Box 2704-6, Beijing, P.R. China.     

δ－Al_2O_3纤维／Al－12Si复合材料室温拉伸强度分析

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度σ＇ｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τｉ．确定复合材料的ＲＯＭ预测曲线，应首先判断σ＇ｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论     

粗粒土渗透变形机制浅析

对砂卵砾石的渗透变形的形成条件进行了简要分析，在此基础上对渗透变形的形式进行了简要评价，并提出了渗透变形临界坡降的计算方法。