喷油方式对斜齿轮齿面温度的影响

为探讨喷油方式对齿面温度的影响，以斜齿轮为研究对象，通过CFD仿真和试验研究不同喷油方式对斜齿轮齿面温度的影响。针对斜齿轮喷油润滑过程的特点，分析其齿面摩擦生热量，简化轮齿喷油润滑计算模型，并基于CFX进行齿面对流换热仿真研究，得到了不同喷油方式下的齿面温度；基于功率开放式斜齿轮试验平台，对不同喷油方式下的齿面温度进行了试验测量，与仿真计算结果进行对比分析。结果表明：在高速重载斜齿轮传动系统中，啮出侧喷油润滑的方式比啮入侧喷油润滑方式的冷却降温效果要好。     

Pressure control of an electro-hydraulic actuated clutch via novel hysteresis model

This paper mainly focuses on the development of pressure tracking control logic of electro-hydraulic actuators for vehicle application. This is done to improve and ensure the performance of a precise lower-level controller for evolving modern shift control logic. The required performance is obtained by hysteresis model-based feed-forward control and additional feedback control. The hysteresis and the time delay, which adversely affect pressure control, are well known nonlinear behaviors in electro-hydraulic actuators. In order to cope with the hysteresis, a novel hysteresis model is proposed based on a physical phenomenon. A mathematical model based on a characteristic curve obtained in preliminary experiments is presented using only one tuning parameter, and this model can be inverted easily to construct a feed-forward controller. In addition, a feedback controller is designed considering the stability margin of a time delay system. The feedback control inputs ensure compensation of the feed-forward errors caused by model error and uncertainty. The proposed controller is designed to lower computational cost considering applicability for production vehicles. As a result, the developed pressure controller is applied to a transmission control unit of a production vehicle and verified experimentally for various driving scenarios.     

双相活齿泵的工作原理

在活齿传动理论及齿轮泵工作原理相结合的基础上，介绍了双相活齿泵的结构及其工作原理，研究结果表明，双相活齿泵具有流量大、流量均匀性好、噪声低以及可变量等优点。     

几种新型联轴器

根据国内外资料，总结了几种新型联轴器，介绍了其工作原理和性能特点。     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

连轧机用人字轮齿轴断裂失效分析

用宏观断口分析、化学检验、力学性能测定、低倍检查、金相组织及夹杂物评定鉴别、受力分析及强度寿命定量估算的方法，对人字轮被动齿轴端断裂失效原因进行分析，并提出改进措施。     

齿轮磨前滚刀的齿形研究

本文介绍了磨前滚刀滚切齿轮的最大根切量和磨后的渐开线长度计算,并建立了数学模型。为更加直观起见,还建立了模拟滚齿的数学模型。并在实验的基础上提出了参考标准。     

内外齿复合冷挤压成型实验研究

通过对轿车转向盘毂件内外齿进行的复合挤压实验研究 ,得到了新式复动式复合挤压模具结构 ,并确定了一种合理的成型工艺方案     

大型对开组合齿圈工艺设计分析及其最优化

本文论述了大型齿圈的结构特征及其现行工艺的合理性；在建立工艺关键环节概念的基础上提出工艺优化方案。并从理论上论证了实现最优化的充分可能性。     

冶金机械设备齿轮减速器的润滑

阐述了冶金设备齿轮减速器润滑问题的重要性，分析了齿轮润滑的主要状态和润滑对齿轮传动的影响，简述了冶金设备齿轮减速机的工作特点及对润滑油性能的要求和选用。