Effects of Cu on the corrosion behavior and microstructure of Mg–Zn–Ca bulk metallic glass

For the purpose of developing biodegradable magnesium alloys with suitable properties for biomedical applications, Mg–Zn–Ca–Cu metallic glasses were prepared by copper mold injection methods. In the present work, the effect of Cu doping on mechanical properties, corrosion behavior, and glass-forming ability of Mg₆₆Zn₃₀Ca₄ alloy was studied. The experimental findings demonstrated that the incorporation of Cu decreases the corrosion resistance of alloys, but increases the microhardness and degradation rate slightly. However, the addition of a trace amount of Cu can make the samples have antibacterial properties. Therefore, Mg–Zn–Ca–Cu has great advantages in clinical implantation and is the potential implant material.     

Modified embedded-atom method interatomic potential for the Mg–Zn–Ca ternary system

Mg–Zn–Ca alloys are representative Mg alloys with high formability at room temperature. Their high formability is thought to be related to slip, twinning, and recrystallization of the alloys, but the detailed mechanisms have not yet been clarified. To enable atomistic simulations for investigating those behaviors, an interatomic potential for the Mg–Zn–Ca ternary system was developed. The development was based on the second nearest-neighbor modified embedded-atom method formalism, combining previously developed Mg–Zn and Mg–Ca potentials with the newly developed Zn–Ca binary potential. The Zn–Ca and Mg–Zn–Ca potentials reproduce structural, elastic, and thermodynamic properties of compounds and solution phases of relevant alloy systems in reasonable agreement with experimental data, first-principles and CALPHAD calculations. The applicability of the developed potentials is demonstrated through calculations of the effects of Zn and Ca solutes on the generalized stacking fault energy for various slip systems, segregation energy on twin boundaries, and volumetric misfit strain.     

轻质滤料滤池的试验与研究

轻质滤料滤池是以比水密度略小的滤料为滤床的滤池，通过以净水厂的原水和污水处理厂的二级处理出水为过滤试验对象，所取得的结果表明：下向流轻质滤料滤池对浊度和悬浮固体（SS）的去除率分别可以达到80％和45％，而滤床的水头损失不超过15cm。因此轻质滤料滤池可以以预过滤的形式配置在过滤处理的净水和污水的处理工艺中。     

脉冲激光诱导Zn/InP掺杂过程中温度分布的解析计算

在实验的基础上 ,分析脉冲激光诱导半导体InP掺杂Zn过程 ,利用简化的一维模型 ,在第三类边界条件下 ,给出一种较直观的脉冲激光辐照有限厚双层材料Zn/InP的温度分布解析形式     

采用纯化学物质校准仪器测定钛合金中碳量

采用纯化学物质对高频加热－红外检测碳硫仪校准，对钛合金中的碳量进行测定。     

有水气藏开发早期可采储量的评价方法

有水气藏是天然气藏中的一个基本气藏类型，其采收率受多种因素的影响，如地面集输压力、井筒混合气水流动的液柱压力和储层物性等，目前普遍采用经验取值、物质平衡和气藏数值模拟等方法进行研究，但由于受开发评价阶段试采资料偏少和气藏数值模拟无法模拟井筒流动等因素的影响，早期采收率计算往往偏差较大，针对这些问题，从气田开发一体化的特点出发，提出了一种全面考虑地层→井筒→地面流动条件下，有水气藏（含凝析有水气藏）发废弃压力的计算方法，发展了利用物质平衡早期预测有水气藏采收率的理论，方法可靠、适用性强，能够推广应用。     

Preparation and Application of Active Composite Antibacterial Material Containing Ag~ and Zn~(2 )

1Introduction Harmfulbacteriaexistanywhereintheworldsuchas soil,air,water,surfacesofobjectsandourskins,etc.Thenumberofbacteriumisenormous,withmanydiffer entspecies.Theyhavethreatenedthehealthofhuman beingsseriously.Withthedevelopmentofeconomyand environme…     

铁液洁净度对凝固热力学参数的影响

为了给高洁净钢连铸细晶技术提供相关理论依据，在高温钼丝炉中通过对电解纯铁加金属铝和硅脱氧，获得不同铁液洁净度的试样。利用差热分析法测定了试样在相同冷却速度下的过冷度。利用凝固过程热力学理论研究了铁液洁净度与过冷度、凝固热力学驱动力、形核功和临界晶核半径等的关系。结果表明：随着铁液洁净度的提高，铁液凝固时的过冷度增大，形核所需的凝固热力学驱动力变大，非均质形核功和临界晶核半径减小。     

不同锌钛比对纳米钛酸锌（ZnO—TiO2）体系成分的影响

以工业偏钛酸、硫酸锌、氨水为主要原料，用直接沉淀法并进行热处理得到钛酸锌粉体，并用XRD对产物成分进行了检测。结果表明，不同的锌钛比对钛酸锌（ZnO-TiO2）体系的成分有较大影响。