泥浆制备中工艺改造的研究

根据室条件下粉磨试验结果，发现球磨过程中筛上料变化存在的突变范围，提出两次加料一次加水可改变泥浆颗粒分布，并找出适宜的加料种类与时间。另外给予测粒度分布提供了宝贵的试验基础数据。     

一种新型功能材料——Ag／Si纳米复合物薄膜的结构及光学性质

采用复合靶及离子微波控制共溅射方法制备了银（Ａｇ）硅（Ｓｉ）复合物薄膜。透射电观察表明，银晶体小颗粒（１－３ｎｍ）镶嵌于非晶基体中。近紫外、可见光及近红外吸收光谱分析表明，当银含量低于５０ａｔ％时，薄膜显示典型非晶半导体光谱特征；当银含量高于５０ａｔ％时，在近紫外及可见波段显示两个吸收峰，讨论了其可能的吸收机制     

磷酸盐激光玻璃中铂颗粒密度与氧化还原平衡关系的研究

用吸收光谱法研究了Ｒ２Ｏ—ＢａＯ—Ｐ２Ｏ５系统磷酸盐激光玻璃中铂颗粒密度与铭的氧化还原平衡的关系。结果表明，玻璃中铂颗粒密度随平衡向右移动而减小；玻璃中平衡随熔炼气氛中氧分压增大、熔炼温度升高而向右移动，当足够大时，铂颗粒不能形成。     

纳米材料应用技术中常见问题随笔

17．何谓固体颗粒的表面改性?固体颗粒表面改性是指采用一定的方法对无机或有机固体颗粒的表面进行处理、精细修饰及加工，有目的改变固体颗粒表面的物理、化学性质，以满足固体颗粒加工及应用的一种技术。     

Analysis of trace mercury in water by solid phase extraction using dithizone modified nanometer titanium dioxide and cold vapor atomic absorption spectrometry

A new method for analysis of trace mercury in water samples was developed, based on the combination of preconcentration/separation using dithizone-modified nanometer titanium dioxide (TiO2) as a solid phase extractant and determination by cold vapor atomic adsorption spectrometry (CVAAS). Dithizone was dissolved with alcohol and loaded on the surface of nano-sized TiO2 powders by stirring. The static adsorption behavior of Hg2 on the dithizone-modified nanoparticles was investigated in detail. It was found that excellent adsorption ratio for Hg2 could be obtained in the pH range of 7-8 with an oscillation time of 15 min, and a 5 mL of 3.5 mol·L-1 HCl solution could quantitatively elute Hg2 from nanometer TiO2 powder. Common coexisting ions caused no obvious influence on the determination of mercury. The mechanisms for the adsorption and desorption were discussed. The detection limit (3σ) for Hg2 was calculated to be 5 ng·L-1. The proposed method was applied to the determination of Hg2 in a mineral water sample and a Zhujiang River water sample. By the standard addition method, the average recoveries were found to be 94.4%-108.3% with RSD (n = 5) of 2.9%-3.5%.     

一种制备磁性粉末的新技术--均匀颗粒成型法

采用均匀颗粒成型法（Uniform Dropler Spray-UDS）制备Fe基合金粉末，该方法制备的颗粒粒度分布均匀，性能一致，大大优于传统的粉末制备方法（如破碎法、气雾化），具有广阔的应用前景。本文分析了粉末制备过程中颗粒尺寸的影响因素，结果表明：颗粒的大小主要取决于坩埚底部小孔、坩埚内外气体压强差以及振荡频率三个独立变量。     

二价金属离子对UASB颗粒污泥的影响

分析了Mg^2 、Ca^2 、Fe^2 等二价金属离子对UASB反应器中厌氧颗粒污泥的影响。     

经等离子体处理的云母粉在聚烯烃中的分散性EI

用图象分析仪测定聚烯烃中云母聚集体数均粒径的结果表明,乙烯等离子体处理云母提高其在聚烯烃中的分散性;强化处理条件有利于云母在LDPE中分散,而对HDPE则不然;云母在PS中的分散性优于在HDPE和LDPE中。     

Observation and Analysis of Gypsum Particleboard using SEM

The microstructures of gypsum board and gypsum particleboard were observed by SEM. The effects of retarder and waterproof agent on the shape and the average dimension of the gypsum crystal were discussed. The mechanism was investigated as well. Four typical instances, i e, the gypsum crystal shape, the gypsum combined with particles on the particles surface, the gypsum combined with particles on the wood cross section and the gypsum combined with particles inside the wood cell cavity were selected and observed. Furthermore, the agglomeration and cementation mechanism between gypsum and particle were studied.     

Microstructure of Nano-Y203／Cobalt Based ,Alloy Composite Coating byLaser Cladding

Composite coatings made of nano-Y203/cobalt-based alloy and produced by crosscurrent CO2 laser on Ni-based superalloy are introduced. Cross-section or surface of the coatings was examined to reveal their microstructure using optical microscope, SEM, including EDS microanalysis, TEM and XRD. The results show that some equilibrium or non-equilibrium phases, such as γ-C0, Cr23C6, Y203 and ε-Co exist in the coatings. Fine and short dendritic microstructure andcolumnar to equiaxed transition (CET) occurred by adding nano-Y203 particles. With the increasing amount of nano-Y203(1%, mass fraction), fully equiaxed crystallization appeared. These are caused by nano-Y203 particles acting as new nucleation site and rapid solidification of the melt. The results also show that inhomogeneous dispersion of nano-Y203 resultsin the formation of ε-Co phase in the coatings. The sub-microstructure of the clad is stacking fault. The mechanism of theformation of equiaxed grains is also analyzed.