开关磁阻直线电机的设计及其推力优化

设计了一种开关磁阻直线电机,使用JMAG软件对其进行了仿真和优化。进行了推力公式的推导,研究了导通顺序和初始位置对电机推力的影响,并分析了三种典型情况的磁力线分布。对电机的定子和动子的齿部和轭部高度、宽度及铁耗进行仿真优化,得出了最优参数。将有取向硅钢应用于该电机,研究了推力与轧制角的关系,并与使用普通硅钢的开关磁阻直线电机进行了对比,推力有一定提升。提出在动子齿部开切向槽的方案,结果表明,开切向槽对推力的影响较小,并能显著减小推力波动。     

Nb和时效时间对热轧中锰TRIP钢中P偏聚的影响

热轧态中锰TRIP钢首先经650 ℃退火2 h,随后在550 ℃进行等温时效热处理,采用场发射扫描电镜(FE-SEM)研究该钢中P的偏聚和时效析出行为的变化情况。结果表明,中锰TRIP钢中P在晶界的偏聚是一种非平衡偏聚现象,临界时间约为50 h,与理论计算结果48 h较为吻合。在局部偏聚区域内,C与P存在共偏聚的关系,即P偏聚量高的地方,C含量也高。而合金元素Nb具有抑制P偏聚的效果,在20~70 h时效时间内,可以相对降低6.57%~19.5%的最大P偏聚量。根据电子背散射衍射(EBSD)菊池线分析,P偏聚量低于2.28at%时,P为固溶状态,高于2.28at.%时,P为析出状态。     

Alloy optimisation of bainitic steel for large plastic mould

Based on the phase transformation theories, especially the T₀ concept of bainite transformation, alloy optimisation of bainitic steel with carbides has been carried out aiming at the produce of plastic mould with large cross-section. The effect of manganese and silicon on proeutectoid ferrite and bainite transformation is explored by dilatometric analysis, XRD and different microscopy techniques. The results show that after the alloy optimisation, the transformation of proeutectoid ferrite is suppressed and when the cooling rate is lower than 0·1°C?s^??1, the new lower bainite transformation appears by decreasing carbon capacity of austenite and promoting carbide precipitation. Industrial production proves that the optimised alloy SDP1 can meet the demand for the plastic mould with the thickness of 1050?mm.     

基于灾度辨识的钢闸门巡视检查研究

巡视检查是对钢闸门要点部位开展定期、定点的信息收集,并对警兆信息做出快速辨识和评估的重要内容。应用灾度辨识的警兆信息评估方法,综合钢闸门巡视检查的各类要素信息,明确工程最大隶属的灾度等级(Ⅰ～Ⅴ级),可作为工程日常巡视检查决策的重要软技术手段。     

Experimental research on dynamic response of PZT-5H under impact load

In order to improve the stability of PZT-based sensors, the mechanical, dielectric, ferroelectric and piezoelectric properties of PZT-5H under impact load were studied experimentally by using the separated Hopkinson pressure bar (SHPB) with an electrical output measurement device. At the same time, the experimental study on the material properties of PZT-5H before and after the impact was carried out. The effect of impact cracks on the output voltage of PZT-5H was also analyzed. The results show that the dynamic piezoelectric constants of PZT-5H under low stress impact (10–50 MPa) are different from those under quasi-static state, and the empirical relationship between them and the peak stress is obtained through experiments. The dielectric properties of PZT-5H did not change under low stress impact, but micro-cracks occurred in the material and dielectric loss increased at high frequencies. Under short circuit, the residual polarization intensity of PZT-5H decreases sharply due to impact load. While the impact load causes the secondary polarization and the increase of the residual polarization intensity of PZT under open circuit. When the stress is over 45 MPa, the PZT-5H breaks. The formation of cracks causes abnormal discharge voltage and gap discharge.     

Economic Indicators

Currency exchanges rates – updated monthly. Economic indicators of industrial production. Countries included: France, Germany, Italy, the United Kingdom, the United States, Canada, Japan (Total G-7), Eurozone and Total EU-28 (Total OECD). Updated monthly. Economic indicators of car registration in the United States, Canada, France, Germany, Italy, Poland, Spain, Turkey, the United Kingdom, Japan, Republic of Korea and Other OECD (Total OECD-30). Updated monthly. Monthly averages of crude steel production in thousand metric tons for the United States, Canada, Brazil, Mexico, Austria, Belgium, Czech Republic, France, Germany, Italy, Netherlands, Poland, Spain, Sweden, Turkey, the United Kingdom, Russia, Ukraine, South Africa, Iran, China, India, Japan, Republic of Korea, Taiwan and Australia.     

Evaluation of expanded gamut software solutions for spot color reproduction

Expanded gamut printing is an approach in color reproduction that expands the color gamut of conventional CMYK printing processes via the use of additional colorants, such as Orange, Green, and Violet inks. This study evaluates the ability of commercial color management software to create an accurate solution for an expanded gamut printing system. In this study, two printing processes were used, an Epson SureColor P9000 inkjet printer/proofer and an HP Indigo 7900 digital production press, both with 7-color expanded gamut ink sets. Software solutions from Alwan, CGS ORIS, ColorLogic, GMG Color, Heidelberg, and Kodak were evaluated. The systems were tested to see how well they could reproduce the colors in the entire PANTONE+ Solid Coated spot color library. It is shown that the solutions are able to reproduce 89% to 94% of the spot colors on the Epson P9000 inkjet printer and 77% to 87% of the library on the Indigo 7900, both to less than two CIEDE2000 (a typical tolerance in label and packaging work). The number of color patches in expanded gamut characterization test charts was noted, as this is still an area of proprietary, nonstandardized working practice. There are many different colorant combinations that can make the same color in expanded gamut printing. The ink build created by the different software solutions was studied, as it relates to press stability through appropriate choice of colorants. Pantone and Adobe provide everyday commercial tools for expanded color workflows. The study identified some issues with products from these companies that could confuse a less-skilled user in a busy production environment. The conclusion of the study is that expanded gamut solutions for spot color printing produce totally acceptable results for digital printing processes; expanded gamut printing is ready, here and now. The findings show that expanded gamut printing can replace cumbersome conventional spot color workflows creating considerable savings and advantages, especially for label and packaging printers.     

Random poly(ε‐caprolactone‐L‐alanine) by direct melt copolymerization

A series of random polyesteramides (PEAs) with a range of molar composition from 90/10 to 50/50 were synthesized by direct melt polycondensation of ε‐caprolactone and l ‐alanine. Their structure was fully characterized by Fourier transform IR and NMR spectroscopy. The resulting copolymers are completely amorphous with the exception of PEA‐90/10 which possesses a semicrystalline structure. These PEAs present increasing glass transition temperatures at increasing l ‐alanine contents and exhibit fairly good thermal stability with 10% mass loss temperatures reaching 315 °C. © 2020 Society of Industrial Chemistry     

Role of Co in formation of Ni-Ti clusters in maraging stainless steel

The effect of Co addition on the formation of Ni-Ti clusters in maraging stainless steel was studied by three dimensional atom probe (3DAP) and first-principles calculation. The cluster analysis based on the maximum separation approach showed an increase in size but a decrease in density of Ni-Ti clusters with increasing the Co content. The first-principles calculation indicated weaker Co-Ni (Co-Ti) interactions than Co-Ti (Fe-Ti) interactions, which should be the essential reason for the change of distribution characteristics of Ni-Ti clusters in bcc Fe caused by Co addition.