基于多目视觉的变形钢板三维测量方法

提出了一种使用4个相机测量变形钢板三维形状的方法;在没有纹理的钢板上画一些点,使用4个相机同时拍摄钢板;利用边缘检测算法找出钢板的边缘,利用特征点提取算法提取出4个图像中钢板上的特征点,并找到4个图像上精确的特征点匹配关系,然后测量出这些特征点的三维点;最后,以这些三维点为种子点向外区域增长,从而得到钢板的三维形状;实验对变形钢板进行三维测量,得到了钢板的精确的三维形状,结果验证了该方法的有效性和可行性。     

不锈钢活性炭滤器的氯腐蚀与防腐

本文就活性炭在预处理中脱氯的不锈钢滤器的氯腐蚀机理进行了探讨，并提出了不锈钢活性炭脱氯滤器的防腐方法和措施。     

A method for observing the three-dimensional morphologies of inclusions in steel

A method for observing the three-dimensional morphologies of inclusions by deeply eroding a steel sample with a kind of organic solution composed of bromine water,acetone,and HC1 (volume ratio,45∶45∶10...     

Corrosion-resistant analogue of Hadfield steel

The concept of alloying austenitic steels with carbon + nitrogen is used for the development of a corrosion-resistant austenitic CrMn steel having an impact wear resistance close to that of the Hadfield steel. A higher stabilization of the austenitic phase by C + N, as compared to carbon or nitrogen alone, is substantiated by ab initio calculation of the electron structure, measurements of the concentration of free electrons and calculations of the phase equilibrium. Based on these results, the compositions (mass%) Cr18Mn18C0.34N0.61 and Cr18Mn18C0.49N0.58 were melted and tested along with Hadfield steel Mn12C1.2. Mechanical tests have shown that, as compared to the Hadfield steel, the experimental steels possess a higher strength, plasticity, hardness and the same resistance to impact wear. TEM studies of the surface layer after impact treatment revealed a mixture of the amorphous phase, nanocrystals and fine-twinned austenite. At the same time, using Mössbauer spectroscopy of conversion electrons, the ferromagnetic ordering was found in the surface layer of up to 10 μm in depth, which is the sign of the strain-induced martensitic phase. The hypothesis of a transition from the low-spin to the high-spin state of the iron atoms within the thin twins in austenite was proposed in order to interpret the discrepancy between TEM and Mössbauer studies. Potentiodynamic measurements and immersion tests show that the CrMnCN steels possess a significantly higher pitting potential and resistance to general corrosion in comparison with Hadfield steel.     

Formation of CaO-TiO2-MgO-Al2O3 dual phase inclusion in Ti stabilized stainless steel

The formation of CaO-TiO2-MgO-Al2O3 dual phase inclusion in 321 stainless steel was investigated in the laboratory. The result indicated that the condition for the formation of CaO-TiO2-MgO-Al2O3 in 321 steel is [Ca]〉0.001wt%, [Ti]〉0.1wt%, and [A1]〉0.01wt%. The mechanism is the following： Al2O3 inclusion turns into CaO-Al2O3 after Ca-Si wire is fed into the molten steel; [Mg] is then obtained by reducing MgO in slag or crucible wall by [Al] and [Ti]; finally CaO-Al2O3 inclusion is changed into CaO-TiO2-MgO-Al2O3 by the reaction with [Mg], [Ti], and [O] in the molten steel simultaneously.     

华龙国际大厦混合结构构件及节点设计

论述了矩形钢管混凝土柱钢框架、混凝土核心筒结构在江西华龙国际大厦的应用，介绍了矩形钢管混凝土混合结构总体设计、节点大样及构造。