弹力竹节牛仔布织造工艺优化

介绍了弹力竹节牛仔布的生产工艺 ,同时对KT36 8剑杆织机织造该织物的工艺进行了优化研究     

Recent advances in isotropic conductive adhesives for electronics packaging applications

Isotropic conductive adhesives (ICAs) have recently received a lot of focus and attention from the researchers in electronics industry as a potential substitute to lead-bearing solders. Numerous studies have shown that ICAs possess many advantages over conventional soldering such as environmental friendliness, finer pitch printing, lower temperature processing and more flexible and simpler processing. However, complete replacement of soldering by ICAs is yet not possible owing to several limitations of ICAs which are mainly related to reliability aspects like limited impact resistance, unstable contact resistance, low adhesion and conductivity etc. Continued efforts for last 15 years have resulted in development of ICAs with improved properties. This review article is aimed at providing a better understanding of ICAs, their principles, performance and significant research and development work addressing the technological utility of ICAs.     

Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.     

HSDPA部署策略及覆盖、容量规划

本文介绍了HSDPA的发展背景,针对HSDPA的主要技术特点,依据市场发展规划、用户需求等方面对HSDPA部署进行探讨,并对HSDPA的覆盖与容量方面进行规划分析.     

Ennoblement of stainless steel in natural seawater – A new explanation

The ennoblement of corrosion potential (E_corr) of passive metal immersed in seawater was investigated with electrochemical technology and epifluorescence microscopy. The in situ observation showed that the bacteria number increased on the metal surface according to an exponential law which was in the same way with the ennoblement of E_corr. At the same time, the anodic polarization current of high‐Mo stainless steel decreased in the initial days. According to the mix‐potential theory and the characteristics of polarization curves of high‐Mo steel in natural seawater, the ennoblement of corrosion potential may be induced by the decrease of the passive current density.     

Cr对低碳Si-Mn系TRIP钢组织与力学性能的影响

主要研究了Cr对低碳Si-Mn系TRIP钢组织与力学性能的影响。首先利用Formastor-F型膨胀仪测定了含Cr和不含Cr两种低碳钢的连续冷却转变(CCT)曲线,分析指出了Cr对连续退火工艺的潜在影响;然后采用Gleeble-3800热/力模拟试验机对两种钢的薄板试样进行了连续退火模拟实验,并通过拉伸试验测定了力学性能;最后采用金相、扫描电镜、X-射线衍射分析等技术考察分析了两种钢的显微组织。结果表明:含Cr的TRIP钢的组织比较细小,铁素体晶粒近似等轴分布;两种TRIP钢的残余奥氏体含量相近,但含Cr钢的残余奥氏体中的含碳量较高。分析认为这是由于含Cr钢在热轧阶段较易生成细小的组织,而在热处理阶段则抑制贝氏体的生成,最终获得稳定的残余奥氏体。     

粉煤灰降失水水泥浆在天然气井固井中的研究与应用

长庆天然气田属于低压、低渗透气田,存在承压能力较低的地层,固井设计要求全井段封固,并且采用双级双凝施工工艺。但由于用于低密度水泥浆中的漂珠生产量降低,价格上升,研究应用替代产品是固井技术发展的方向。在一级领浆中研究应用了粉煤灰水泥浆体系,其性能和固井质量可完全满足固井要求。粉煤灰水泥浆体系价格低和固井质量优良,使其成为漂珠水泥浆体系的替代配方。     

反应器和钢烟囱整体吊装的难点和对策

介绍了在金陵石化炼油厂200万t/a柴油加氢装置建设中,将质量为237t的反应器和高60m的钢烟囱成功进行整体吊装过程中的关键技术.通过此项工程实践得出以下结论象钢烟囱这样细长重物的整体吊装,由两台吊车抬立起后,再由主吊车独立吊装就位的施工方法简单易行,安全可靠,应用范围广;结构复杂细长杆的吊装强度和挠度计算比较复杂,在计算过程中可以忽略部分次要件的质量,分别以两吊点为支点计算上下吊点所受的力,然后再按比例放余量,使两吊点受力之和等于细长杆的重力,计算挠度时,可以适当地把问题夸大化,从而建立近似的力学模型;高压厚壁重型容器的吊装,宜直接设置专门吊盖与大法兰用螺栓把紧起吊;施工现场地基坚实是保证吊车站位和吊装施工的前提条件.     

稀土改善09CuPTiRE耐候钢耐蚀性的作用机理

应用扫描电镜(SEM)、离子探针(IMA)、X射线光电子能谱(XPS)和交流阻抗法研究含不同稀土耐候钢稀土提高耐大气腐蚀作用机理。结果表明,合适的稀土含量可显著提高钢的耐腐蚀性,稀土能促进Si、Cu和P在内锈层中以Si~(4+)、Cu~+和P~(5+)形态富集,并观察到锈层中的稀土。钢中加入稀土形成了致密连续厚而粘附性好的含硅铜稀土的复合铁锈层,从而提高了抗大气腐蚀性能。     

32位MIPS微处理器中乘法器的设计和实现

在Booth算法的基础上,结合MIPS 4KC微处理器中的流水线结构和乘法器的工作过程,提出了一种改进的Booth乘法器的设计方法,并采用全制定方法实现,用这种方法实现的乘法器单元具有面积小、单元电路可重复性好、版图设计工作量小、功耗低等特点.