Modified atmosphere packaging of a mixed prepared vegetable salad dish

The aim of this study was to design a modified atmosphere package for a mixed vegetable salad consisting of 75 g of cut carrot, 55 g of cut cucumber, 20 g of sliced garlic and 50 g of whole green pepper. Respiration data of all the components were combined with film permeability data to predict package atmospheres and design optimal packages for experimental testing for improved shelf-life of the produce. The optimal package avoided minimum O₂ and maximum CO₂ tolerance limits, and chilling injury temperatures for any component. A pouch form package made of 27 mm low density polyethylene developed a modified atmosphere of 2.0–2.1% O₂ and 5.5–5.7% CO₂, which was beneficial for all components and provided better quality retention than other test packages.     

新一代的国际互联网通信协议：IP Version6

本文通过对ＩＰｖ６和ＩＰｖ４协议的比较，讨论了新一代国际互联网通信协议ＩＰｖ６的特点，新增加的功能，并指出ＩＰｖ６协议的颁布对现有技术的影响和相应对策。     

Ti,N,Mg对M2高速钢凝固组织和硬度的影响

为了改善Ｍ２高速钢共晶碳化物的分布，本文利用小凝固试样变质的方法研究了Ｔｉ，Ｎ和Ｍｇ对Ｍ２高速钢凝固组织和硬度的影响。试验结果表明，加入Ｔｉ或Ｔｉ－Ｎ后，共晶碳化物形态和分布有很大改善，而加入Ｔｉ－Ｎ后对凝固组织有轻微的细化作用，但只添加Ｔｉ不补碳时，钢的淬火硬度和回火硬度均下降；加入适量的Ｍｇ可以使片状的Ｍ２Ｃ型共晶碳化物转为鱼骨状的Ｍ６Ｃ型共晶碳化物，使其分布有所改善，Ｔｉ和Ｍｇ复合加入可以明     

Immobilization of inert TRISO-coated fuel in glass for geological disposal

Vitrification of TRISO-coated gas reactor fuel particles was achieved via two methods: glass melting and sintering. Inert TRISO-coated fuel particles and a borosilicate glass were used. With glass melting at 1200-1300 °C floatation and decomposition of carbon and silicon carbide occurred. Thermal pre-treatment of the particles for oxidation of pyrocarbon did not improve the coating properties of the glass. During cooling most of the particles floated and sorbed on the crucible or mold walls. The sintered glass at 700 °C showed better coating properties of the TRISO-coated fuel particles despite higher porosity compared to glass made by melting. Aqueous leaching properties of glass with particles are similar regardless the mode of fabrication, indicating the good chemical durability of the sintered glass. Sintered glasses may constitute a good technique for TRISO-coated fuel particles immobilization for an eventual deep geological disposal.     

Microstructure and Mechanical Properties of Heat-treated GeSb_2Te_4 Thin Films

The effect of annealing on microstructure,adhesive and frictional properties of GeSb 2 Te 4 films were experimentally studied.The GeSb 2 Te 4 films were prepared by radio frequency(RF)magnetron sputtering,and annealed at 200℃and 340℃under vacuum circumstance,respectively.The adhesion and friction experiments were mainly conducted with a lateral force microscope(LFM)for the GeSb 2 Te 4 thin films before and after annealing.Their morphology and phase structure were analyzed by using atomic force microscopy(AFM)and X-ray Diffraction(XRD)techniques,and the nanoindention was employed to evaluate their hardness values.Moreover,an electric force microscope(EFM)was used to measure the surface potential. It is found that the deposited GeSb 2 Te 4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition;the adhesion has a weaker dependence on the surface roughness,but a certain correlation with the surface potential of GeSb 2 Te 4 thin films.And the friction behavior of GeSb 2 Te 4 thin films follows their adhesion behavior under a lower applied load.However,such a relation is replaced by the mechanical behavior when the load is relatively higher.Moreover,the GeSb 2 Te 4 thin film annealed at 340℃presents a lubricative property.     

酸催化二甘醇脱水环化反应研究

以硫酸、磷钨酸、ZRP-5分子筛为催化剂,研究了二甘醇(DEG)脱水环化的反应规律。结果表明,DEG发生分子内脱水环化反应,生成1,4-二氧六环(DOX),DEG分子间脱水不仅可以生成四甘醇、六甘醇等,同时可生成三甘醇、五甘醇等一系列的多甘醇(PEG)。不仅DEG可以脱水环化生成DOX,在反应中生成的PEG也同样可以进行生成DOX的反应。对于二甘醇(DEG)脱水环化反应,硫酸是性能优良的催化剂,反应可以在较低的温度下进行,馏出产物中DOX选择性大于95％。     

常减压蒸馏装置阻垢剂进料管腐蚀与防护

通过对常减压蒸馏装置阻垢剂进料管的材质、性能、工作条件及腐蚀形貌、腐蚀产物的全面分析,找出了使进料管发生大面积腐蚀的腐蚀介质为环烷酸.并提出了减缓阻垢剂进料管环烷酸腐蚀的措施,主要包括选用更耐蚀的316或316 L材质以及改进三通结构等.     

p,V, T and derived thermodynamic data for toluene,trichloromethane, dichloromethane,acetonitrile, aniline,and n-dodecane

Experimentally determined p,V,T data are reported for toluene, trichloromethane, dichloromethane, acetonitrile, aniline, and n-dodecane at 278, 288, 298, 313, and 323 K, except for dichloromethane, for which the highest temperature was 298 K. At each temperature, measurements were done at pressures up to about 280 MPa or (for aniline and n-dodecane) at a lower pressure slightly below the freezing pressure at the temperature of measurement. Values of the isobaric expansivity isothermal compressibility and (for toluene, trichloromethane, dichloromethane, and acetonitrile) internal pressure, derived from the p,V,T data, are presented.     

The development of a stress analysis code for nuclear graphite components in gas-cooled reactors

Most of the UK nuclear power reactors are gas-cooled and graphite moderated. As well as acting as a moderator the graphite also acts as a structural component providing channels for the coolant gas and control rods. For this reason the structural integrity assessments of nuclear graphite components is an essential element of reactor design. In order to perform graphite component stress analysis, the definition of the constitutive equation relating stress and strain for irradiated graphite is required. Apart from the usual elastic and thermal strains, irradiated graphite components are subject to additional strains due to fast neutron irradiation and radiolytic oxidation. In this paper a material model for nuclear graphite is presented along with an example of a stress analysis of a nuclear graphite moderator brick subject to both fast neutron irradiation and radiolytic oxidation.