热强钛合金BT25组织与性能

介绍了前苏联航空发动机用热强钛合金（或高温钛合金）BT25的发展概况，并对BT25合金的成分特点、热处理强化优点等做了进一步阐述，给出了退火状态下的物理性能，在说明热强钛合金微观组织与力学性能关系的基础上给出了BT25合金的各种力学性能。     

尿素对以硝酸铝和葡萄糖为原料合成氮化铝粉末反应过程中相变及反应速率的影响

以硝酸铝(Al(NO3)3·9H2O)和葡萄糖(C6H12O6·H2O)为原料,利用碳热还原法制备氮化铝粉末,研究了尿素对前驱物的制备及前驱物氮化反应的影响,研究发现添加尿素合成的前驱物和未添加尿素合成的前驱物在氮化反应过程中相变和反应速率存在较大差异。在没有添加尿素合成的前驱物的氮化反应过程中,出现了γ-Al2O3、α-Al2O3、AlON和AIN相,该前驱物的反应速率慢,完全氮化需要在1600℃下才能完成。对于添加尿素合成的前驱物而言,在其氮化反应过程中仅出现了γ-Al2O3和AIN相,没有α-Al2O3和AlON的生成,AIN直接由γ-Al2O3氮化生成,该前驱物的氮化反应速率快,氮化反应温度低,在1400℃下即可实现完全氮化。分析讨论了两种前驱物的氮化反应速率不同的主要原因,并利用XRD、SEM等分析方法对粉末进行了表征。     

MCM用氮化铝共烧多层陶瓷基板的研究

通过实验优化AlN(氮化铝)瓷料配方及排胶工艺,对共烧W(钨)导体浆料性能及AlN多层基板的高温共烧工艺进行了研究,并对AlN多层基板的界面进行了扫描电镜分析。采用AlN流延生瓷片与W高温共烧的方法,成功地制备出了高热导率的AlN多层陶瓷基板,其热导率为190 W/(m·K),线膨胀系数为4.6106℃1(RT~400℃),布线层数9层,W导体方阻为9.8 m,翘曲度为0.01 mm/50 mm,完全满足高功率MCM的使用要求。     

添加CaF2-YF3的AlN陶瓷的热导率

用CaF2和YF3做添加剂，在1750℃制备了热导率高于170W/m.K的的AlN陶瓷，并用XRD和SEM研究了AlN陶瓷在烧结过程中的相组成，微结构以及晶格参数的变化，并讨论了其对热导率的影响，研究发现，当使用CaF2-YF3做添加剂时，微结构差异对AlN陶瓷热导率的影响很小，AlN陶瓷的热导率主要由AlN晶格氧缺陷浓度决定，由于CaF2-YF3能有效降低AlN颗粒表面的氧含量，从而有利于获得高的热导率。     

Homogeneous Plastic Flow of Fully Amorphous and Partially Crystallized Zr_(41.2)Ti_(13.8)Cu_(12.5)Ni_(10)Be_(22.5) Bulk Metallic Glass

The homogeneous plastic flow of fully amorphous and partially crystallized Zr(41.2)Ti(13.8)Cu(12.5)Ni(10)Be(22.5) bulk metallic glass (Vitl) has been investigated by compression tests at high temperatures in supercooled liquid region. Experimental results show that at sufficiently low strain rates, the supercooled liquid of the fully amorphous alloy reveals Newtonian flow with a linear relationship between the flow stress and strain rate. As the strain rate is increased, a transition from linear Newtonian to nonlinear flow is detected, which can be explained by the transition state theory. Over the entire strain rate interval investigated, however, only nonlinear flow is present in the partially crystallized alloy, and the flow stress for each strain rate is much higher. It is found that the strain rate-stress relationship for the partially crystaltized alloy at the given temperature of 646 K also obeys the sinh law derived from the transition state theory, similar to that of the initial homogeneous amo     

LF6铝合金的超塑性／扩散连接组合工艺试验及理论研究EI

本文研究了ＬＦ６铝合金的超塑性／扩散连接组合工艺，用变形和再结晶的方法细化晶粒，成功地进行了ＳＰＦ／ＤＢ工艺试验，利用电子探针观察了扩散连接接头的界面微观区域，并从机理上分析了金属的超塑性／扩散连接两种工艺之间的内部联系及其金属学行为。     

铸造铝合金(ZL109)激光表面处理

采用功率为2kW级CO_2连续可调式横流激光光源,对不同涂层的ZL109试样表面进行了激光熔凝的实验研究。     

The influence of NaCl and CO2 on the atmospheric corrosion of magnesium alloy AZ91

The influence of NaCl and CO₂ on the atmospheric corrosion of magnesium alloy AZ91 is studied in the laboratory. Samples were exposed under carefully controlled air and flow conditions; the relative humidity was 95%, the temperature was 22.0°C and the concentration of CO₂ was < 1 ppm or 350 ppm. Different amounts of sodium chloride (0–70 μg/cm²) were added before exposure. The corrosion products were analyzed by gravimetry, ion chromatography, X‐ray diffraction and scanning electron microscopy. Mass gain and metal loss results are reported. The combination of high humidity and NaCl is very corrosive towards AZ91. However, the NaCl‐induced corrosion is inhibited by ambient concentrations of CO₂. Exposure in the absence of CO₂ gives rise to heavy pitting, with brucite, Mg(OH)₂, being the dominant corrosion product. In the presence of CO₂ a layer of hydrated magnesium hydroxy carbonate, Mg₅(CO₃)₄(OH)₂ · 5 H₂O forms. A tentative corrosion mechanism is presented that explains the behavior in the two environments.     

Microstructural changes accompanying repair welding in 5xxx aluminium alloys and their effect on the mechanical properties

At the shipyards, the aluminium alloy 5083 is welded with a multi-pass sequence using the metal inert gas technique. If, while checking the weld integrity either after welding or during service, defects are detected in the vicinity of the weldment, repairs are usually employed to extend the service life.

The repair method involves removal of the upper passes, depending on the thickness and re-welding under the same conditions.

Purpose of this paper is to examine the microstructural changes accompanying repair welding, define their effect on properties of primary importance and set, if possible, an upper limit as far as the number of repairs is concerned.