反舰导弹突防能力研究

分析了典型目标舰艇防空武备的配置及其反舰导弹的抗击过程，计算了某型反舰导弹对该型舰艇的突防概率，并对结果进行了分析。     

The Deep Structure of the Picturesque

The late Paul Coates was one of the first students at the Architectural Association (AA) in London to submit an international computation-based diploma, in 1969. Responsible for introducing a series of computational techniques, Coates was also the founder of the MSc in Computing and Design at the University of East London, and in 2002 the Centre for Evolutionary Computing in Architecture (CECA). In this unpublished article from 2008, which has been prepared and rewritten for publication by Christian Derix , Coates recounts his pursuit of ‘the particle physics of architecture’ - geometric rules that inform both unplanned and planned human occupation of space.     

Study and evaluation of abrasive water jet turning process performance on AA5083

In this study, the effect of processing parameters on surface roughness and macro surface characteristics was analyzed during the machining of Ø30 mm and 300 mm aluminum alloy AA5083 abrasive water jets. As the processing parameters (up to 10 mm min⁻¹, 15 mm min⁻¹, 20 mm min⁻¹ and 25 mm min⁻¹), abrasive flow rate (50 g min⁻¹, 150 g min⁻¹, 250 g min⁻¹ and 350 g min⁻¹), the lathe chuck rotational speed (25 min⁻¹, 50 min⁻¹, 75 min⁻¹ and 100 min⁻¹) and the nozzle approach distance (2 mm, 5 mm, 8 mm and 11 mm) were used in experiments. In experimental studies, the pump pressure (360 MPa) was used as a constant, in the form of an abrasive Garnet (100 mesh), and the nozzle diameter as 0.76 mm. According to the findings, the best results in terms of surface roughness were obtained as a result of turning speed and abrasive flow rate. When the macro surface characteristics were examined, it was found that the lathe chuck rotational speed increased, the rate of nozzle progression was low, the rate of abrasive flow was high and the nozzle approach distance was lower and the smoother surfaces were obtained.     

不确定系统稳定性的仿射不等式分析

针对不确定系统的区间表示不能描述变量间的相关性,相应的区间算法容易导致误差爆炸的缺点,提出了不确定系统的仿射表示法及系统稳定性的仿射不等式判断方法.首先将系统中的不确定信息用仿射参数来表示,得到不确定控制系统传递函数的仿射形式,然后通过求解含仿射参数的不等式组求得了满足系统的稳定性条件时各噪声允许的范围.算例表明,由于考虑了变量间的相关性,相对于区间算法,所提方法可以在更大的不确定范围内判断出系统的稳定性,算例验证了该方法的有效性.     

Formability and cavitation behavior of superplastic AA5083 aluminum alloy under biaxial tension

The superplastic forming potential of two fine-grained 5083 aluminum alloys were studied under biaxial tension using a pneumatic bulge test. Experiments were performed at temperatures ranging from 475 to 525 ℃ with three different strain paths ranging from equi-biaxial to approaching plane strain. The shape of the forming limited diagram（FLD） is found to be significantly different from FLDs commonly used in room temperature stamping. The effects of temperature on final thickness distribution, dome height and cavitation were investigated for the case of equi-biaxial stretching. Increasing temperature in free bulge forming can improve the thickness distribution of final parts but have no significant effect on dome height. The results indicate that determination of forming limits in SPF cannot be represented with a simple FLD and additional metrics such as external thinning and internal cavitation needed to determine the SPF potential of a material.     

AA5083铝合金在海水中的腐蚀行为研究

采用电化学工作站研究了AA5083铝合金在海水中的极化曲线、点蚀电位、交流阻抗等性能,通过高分辨率数码显微镜、扫描电镜等表征手段对AA5083铝合金腐蚀前后的表面形貌进行了研究。研究结果表明:AA5083铝合金在静态海水中的腐蚀以点腐蚀为主,浸泡初期阻抗由容抗和感抗组成,腐蚀电位随着浸泡时间的延长不断负移,耐腐蚀性降低,点腐蚀坑越来越多,并且点腐蚀坑不断增大加深,在试板表面中间区域形成半球状点腐蚀坑,腐蚀达到一定程度后,出现Warburg阻抗,腐蚀电位逐渐稳定在-0.58V。     

共聚物钻井液降滤失剂的合成与性能评价

以丙烯酰胺(AM)、2-甲基-2-丙烯酰胺基丙磺酸(AMPS)、丙烯酸(AA)、甲基丙烯酰氧乙基三甲基氯化铵(DMC)为原料,采用氧化还原引发体系合成了一种四元共聚物水基钻井液降滤失剂。确定了最佳合成条件:单体配比为AM/AMPS/AA/DMC=55∶30∶10∶5(质量比),引发剂加量各为0.3%(单体浓度为1),单体总浓度为20%(质量分数),反应温度为50℃,溶液p H值为7,反应时间为4 h。对聚合物进行了红外表征,合成产品与设计结构一致。钻井液性能评价结果显示:淡水基浆中聚合物加量为0.7%时,常温中压滤失量为6.0 m L,经过180℃老化后,API滤失量为8.2 m L,高温高压滤失量为11.6 m L;聚合物加量为1.0%时的页岩相对回收率达到99.4%。说明AM/AMPS/AA/DMC聚合物降滤失能力强,且热稳定性和抑制性能好。     

Formability and failure mechanisms of AA2024 under hot forming conditions

Aluminium alloy 2024 (AA2024) is extensively used as a structural material in the aircraft industry because of its good combination of strength and fatigue resistance. However, complex shaped components, particularly those made from sheet, are extremely difficult to form by traditional cold forming due to its low ductility at room temperature. A possible solution of this problem is to form sheet workpieces at elevated temperature. The aim of the work described in this paper is to determine the relationship between formability and temperature for AA2024 by conducting a series of tensile tests at elevated temperatures ranging from 350 to 493 °C. Ductility of AA2024 was found to increase gradually with increasing temperature up to 450 °C, followed by a sharp decrease with further increase in temperature. So-called cup tests confirmed that the formability of AA2024 is very high at a temperature of about 450 °C. Fracture surfaces and longitudinal sections of formed samples were examined by scanning electron microscope. It was found that fracture occurred in three different modes depending upon the temperature, and the sharp decrease in ductility when the temperature exceeds 450 °C was caused by softening of grain boundaries by solute enrichment (at higher heating rates liquation may be involved) and softening of the matrix around inclusion particles.     

Comparison of nutritional and nutraceutical properties in cultivated fruits of Fragaria vesca L. produced in Italy

Individual sugars, organic acids, total polyphenols, vitamin C and antiradical activity (as measured by DPPH method) were quantified in cultivated Fragaria vesca berries, comparing different varieties (Regina delle Valli, Alpine, Sara and Valitutto) and different environments with regard to altitude. Cultivar effect mainly influenced the concentration of total polyphenols and antiradical activity which are strongly correlated (R² = 0.91; P = 0.001); conversely, altitude seemed to exert an influence in sugar and organic acid composition. The comparison of the general quality of the most diffused cultivar of F. vesca (Regina delle Valli and Alpine) evidenced that both cultivars have the same nutritional properties, whereas Regina delle Valli is better than Alpine from the point of view of total polyphenolic content (716 vs 471 mg catechin/100 g fresh weight) and radical scavenging activity (301 vs 219 ml DPPH solution/100 g fresh weight), thus resulting more attractive from the health protecting attributes point of view. F. vesca berries showed also a concentration of sugars, citric acid, malic acid and total polyphenols much higher than those reported in literature for Fragaria x ananassa.     

香蕉低聚糖的通便功能评价

为比较不同品种香蕉低聚糖的通便功能,选取皇帝蕉(Musa AA Pisang Mas)和粉蕉(Musa ABB Pisang Awak),提取低聚糖后分别设置两种浓度(高剂量组2.5 g/(kg·BW·d)和低剂量组1.25 g/(kg·BW·d)),参考《保健食品检验与评价技术规范(2003版)》中\