机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。     

大块非晶合金的性能、制备及应用

综述了大块非晶合金的性能、制备方法及应用，对比了吸铸法制备的棒状Zr41.2Ti13.8Cu12.5Ni10Be22.5,Zr57Cu20Al10Ni8Ti5,Zr52.5Ti5Cu17.9Ni14.6Al10(原子分数)大块非晶样品的过冷温度区间宽度(△Tx)，给出了3种大块非晶合金系列的热稳定性参数Tg、Tx及△Tx，提出了大块非晶合金领域存在的问题及发展方向．     

数字下变频器GC1012B原理及配置方法

数字下变频技术是软件无线电的一项核心技术,其性能的好坏直接影响数字接收机的精度。GC1012B是美国TI公司推出的新型数字下变频器。文中从GC1012B的结构特点和内部功能框图出发,分析其工作原理,并介绍GC1012B几个主要寄存器的配置方法,从而实现对频率、滤波模式、增益大小等参数的设置。最后给出了一个具体配置实例作为参考。     

Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.     

自动力套管补贴加固技术及其在B125井的应用

随着油田开发时间的延长，油水井井下套管的损坏将越来越严重，套管故障井将越来越多，为了恢复套损井生产，将套管损坏所造成的损失降到最低，在配套波纹管补贴，水动力补贴，爆炸补贴等专门修套技术的基础上，通过认真调查研究，又配套了操作方便简单，适用套管损坏类型广的自动力套管补贴加固技术，使各种套管变形，套管断错（错开没有位移或位移量不大时）、套管破裂，误射孔井段封堵，已射开水层封堵等修井作业的难度进一步降低，从而进一步提高了修复井综合开发经济效益。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

化学镀非晶态Ni—B合金的研究

本文通过化学镀方法在铜和钢上沉积非晶态Ni-B合金。着重讨论了还原剂浓度、络合剂浓度对化学镀沉积速率的影响;分析了它的耐蚀原因和其显微硬度随退火温度的变化情况并就其应用和发展略作说明。     

钨合金圆筒爆破试验破片分布的统计分析

采用圆筒爆破试验方法研究了易碎型钨合金的破片分布特征,并与93W合金的结果进行了对比.对破片的数量和质量分布特征进行了统计分析,发现易碎型钨合金的破片率明显高于93W合金,而且破片的均匀性也明显好于93W合金,但易碎钨合金的破片回收率低于93W合金,而且受装药量的影响较大.     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。