Tool wear mechanism in turning of novel wear-resisting aluminum bronze

1　ＩＮＴＲＯＤＵＣＴＩＯＮＡｌｕｍｉｎｕｍｂｒｏｎｚｅｉｓａｎｉｍｐｏｒｔａｎｔｅｎｇｉｎｅｅｒｉｎｇｍａｔｅｒｉ ａｌｄｕｅｔｏｉｔｓｅｘｃｅｌｌｅｎｔｐｈｙｓｉｃａｌ ,ｍｅｃｈａｎｉｃａｌ,ａｎｔｉ ｃｏｒｒｏ ｓｉｏｎａｎｄｗｅａｒｒｅｓｉｓｔｉｎｇｐｒｏｐｅｒｔｉｅｓ .Ｏｕｒｒｅｓｅａｒｃｈｇｒｏｕｐｄｅ ｖｅｌｏｐｅｄａｓｐｅｃｉａｌｔｙｐｅｏｆｈｉｇｈｓｔｒｅｎｇｔｈ ,ｗｅａｒ ｒｅｓｉｓｔｉｎｇａ ｌｕｍｉｎｕｍｂｒｏｎｚｅ(ＫＫ ) ,ｗｈｉｃｈｉｓｅｘｃｅｐｔｉｏｎａｌｌｙｇｏｏｄｆｏｒ…     

Structure/property relationships in sintered and thermally sprayed WC-Co

Thermally sprayed WC-Co is widely used as a wear-resistant coating for a variety of applications. Although it is well established that thermal spray processes significantly affect chemistry, microstructure, and the phase distribution of WC-Co coatings, little is known about how these changes influence wear resistance. In this study, the microstructure and wear behavior of sintered and thermally sprayed WC-Co materials are examined. Powders of WC-12 wt% Co and WC-17 wt% Co were pressed and sintered, as well as thermally sprayed by high-velocity oxy-fuel (HVOF), air plasma spray (APS), and vacuum plasma spray (VPS) techniques. Results indicated considerable differences in the resulting microstructures, mechanical properties, and wear resistance. The thermally sprayed coatings showed anisotropic fracture toughness, whereas the sintered materials did not. It was also shown that a combined mechanical property/microstructure parameter, based on considerations of indentation fracture mechanisms, can be used in most cases to describe abrasive and erosive wear resistance of thermally sprayed WC-Co materials as follows: Wear resistance a whereK _ic is the indentation fracture toughness,H is hardness, andV ^Co _f is the volume fraction of cobalt. This relationship provides a means for assessing wear resistance of WC-Co coatings intended for industrial applications requiring abrasion and/or erosion resistance.     

高铝锌基合金粉末冶金材料及其摩擦学特性初探

初步研究了高铝锌基合金的粉末冶金工艺及其材料的摩擦磨损性能。通过气喷气冷法制取合金粉末，用压制后真空烧结的方法制备高铝锌基合金粉末冶金材料。实验结果表明，高铝锌基合金的粉末冶金试样在干摩擦和油润滑条件下的磨损率及摩擦系数均小于同一合金的铸造试样，但其压溃强度有待提高。在实验的基础上还探讨了该材料的耐磨减摩机理     

WCp增强钢基表层复合材料的两体磨粒磨损性能

在室温条件下,选用销盘磨粒磨损试验机,绿碳化硅磨料,研究增强相WC颗粒直径对WCp增强钢基表层复合材料磨损性能的影响,以正火ZG45作为标样,计算相对耐磨性ε值.研究结果表明,WCp增强钢基表层复合材料相对于正火ZG45的相对耐磨性ε值,随其增强相WC颗粒直径的变小而降低,当增强相WC颗粒直径大于150μm时,相对耐磨性ε值高达40左右,而当增强相WC颗粒直径小于100μm时,相对耐磨性ε值降低到5以下.     

离子束增强沉积CrN膜层及其微动摩擦学性能研究

以不同氮离子辅助轰击能量制备CrN膜层．利用纳米压入仪及显微硬度计分别测试单晶Si片上膜层的硬度及断裂韧度K1C．使用XRD、XPS及EPMA分析离子轰击能量对镀层组织结构的影响。结果表明，采用能量较低的氮离子轰击得到的涂层，由于金属Cr的存在，涂层硬度虽有所降低，但断裂韧度K1C数值较高。选择较低的4keV辅助轰击能量，在M2高速钢基体上沉积CrN涂层，膜层在空气介质中表现出优异的耐磨减摩特性.但在水介质条件下，由于膜层接触区域的去钝化，再钝化使腐蚀和磨损相互加速，导致CrN膜层摩擦系数，尤其是磨损量明显高于基材。     

Fabrication and Characterisation of Rutile-TiO_2 Coatings on Metallic Alloy Substrates

RUTILE-TJO2is a versatile material possessing manyinteresting physical,chemical,optical and dielectricproperties[l].It is also a good tribological material thatcan offer low friction and low wear rate[2,3].However,the application of rutile in the tribological field hasbeen limited to titanium alloys only so far,for example,by thermal oxidation of titanium alloys[4,5].Very fewinvestigations have been directed to the tribologicalapplications of rutile films on substrates other thantitanium al…     

激光淬火铁基烧结材料的摩擦与磨损

研究了两种不同成分铁基烧结材料经宽带激光表面处理后的显微组织和摩擦学特性。结果表明，铁基烧结材料的耐磨性显著提高。两种材料相比，在较低载荷下，组织为孪晶马氏体／位错马氏体混合材料具有较好的摩擦学特性。而在较高载荷下，组织为马氏体／下贝氏体复相的材料具有较好的摩擦学特性。     

铸钢件耐磨堆焊层人工神经网络成分预测

阐述了人工神经网络在耐磨铸钢堆焊成分预测中的意义和工作原理，用自行编制的人工神经网络程序计算了铸钢件堆焊层的化学成分。     

高铬铸铁变温马氏体相变与摩擦诱发马氏体相变关系的研究

对三种含Mn、Si、Mo亚共晶高铬铸铁的变温马氏体相变进行了DSC分析,并对表层的摩擦诱发马氏体做了X射线衍射分析。结果表明,变温马氏体相变前期,马氏体形核、长大阻力较大。在M_s温度相近的情况下,变温马氏体相变形核、长大速率快的,其摩擦诱发马氏体量也多。