基于ANSYS的闩体刚强度有限元分析

闩体的刚度和强度必须满足设计要求。用有限元法对复杂结构件进行力学性能分析是非常有效的方法。采用ANSYS软件对闩体进行了刚度和强度分析,得出了有用的结论,可供相关设计借鉴。     

Multidisciplinary optimization of gas-quenching process

Distortion as a result of the quenching process is predominantly due to the thermal gradient and phase transformations within the component. Compared with traditional liquid quenching, the thermal boundary conditions during gas quenching are relatively simple to control. By adjusting the gas-quenching furnace pressure, the flow speed, or the spray nozzle configuration, the heat-transfer coefficients can be designed in terms of both the component geometry and the quenching time. The purpose of this research is to apply the optimization methodology to design the gas-quenching process. The design objective is to minimize the distortion caused by quenching. Constraints on the average surface hardness, and its distribution and residual stress are imposed. The heat-transfer coefficients are used as design variables. DEFORM-HT is used to predict material response during quenching. The response surface method is used to obtain the analytical models of the objective function and constraints in terms of the design variables. Once the response surfaces of the objective and constraints are obtained, they are used to search for the optimum heat-transfer coefficients. This process is then used instead of the finite-element analysis. A one-gear blank case study is used to demonstrate the optimization scheme.     

碳纳米管及稀土元素钇(Y)对高Ni含量Ti(C,N)基金属陶瓷组织与性能的影响

研究了不同含量的碳纳米管及0.8%稀土Y对高Ni含量Ti(C,N)基金属陶瓷组织性能的影响.将不同成分的试样分别于1400℃、1410 ℃、1420℃真空烧结,测试抗弯强度、洛氏硬度,观察背散射电子形貌、断口形貌并做能谱分析.结果表明,加入质量分数(下同)为0.8%Y及0.3%～1.0%的碳纳米管时,碳纳米管含量为0.5%的组织较均匀,芯壳结构明显,抗弯强度及硬度均较高.     

Numerical Analysis of the Constrained Blister Test

The constrained blister test is investigated through finite element analysis to determine the applicabilities and the limitations of the new technique. Numerical results confirm that the strain energy release rate asymptotically approaches a constant value. These results also show that the test technique and the approximate solution for strain energy release rate are applicable for some practical cases.     

生物质中元素分布特征的聚类分析研究

测定了稻草秆、小麦秆、玉米秆、棉花秆、大豆秆、玉米芯、花生壳和柳树、松树、桦树、杨树、杉树 1 2个农业生物质和林业生物质种类 2 7个样品中主要元素 K,Ca,Na,Mg,Al,Fe,P和痕量元素 As,Cr,Co,Cu,Cd,Mn,Mo,Ni,Pb,Ti,Zn,V,Si,Ba,Be,Se,Sb,Ge,Hg的含量 ,并用SPSS聚类分析法分别进行了 R型和 Q型聚类研究 ,对这些元素在生物质中的分布特征进行了研究 .结果显示 :杨木、杉木和桦木与松木和柳木归成一大类 ,经济类作物黄豆秆和棉花秆分别归类后又归入一大类 ;农业生物质稻草秆和小麦秆、玉米秆被归入一类 ;虽然 2 7种生物质样品分别取自我国东北、华东、华北和西南地区 ,在地理位置上相距极远 ,但样品聚类谱系图表明 ,元素的分布特征与生物质的种类的关系显著 ,与产地的关系不明显 ,即元素的分布特征受种类的影响大 ,而受生长环境、气候、土壤条件的影响小 .     

玻璃钢筋混凝土的有限元计算与试验

钢筋混凝土广泛应用于土木工程领域，但其结构耐久性因钢筋本身的锈蚀成为现今急待解决的问题。人们一直在寻找对钢筋混凝土进行改良的途径，用玻璃钢筋代替普通钢筋是解决这一问题的一个有效的方法，为此进行了试验和ANSYS有限元分析，结果证明此法具有可行性。     

Discrete element approach for mine dump stability analysis

Mine overburden dumps have posed significant safety issues in the operations of various unit operations of open pit min-ing especially the external dumps. The external dumps are composed of a mixture of fragmented rocks and loose soil. Their charac-teristic is comparable to heavily discontinuous solid mass. The conventional approach of limit equilibrium methods provide safety factors for the slope but nothing about the stress-strain characteristics of the large dump mass. The designs of dump location and their respective geometry are integrated for the know-how of the stability characteristics of these dumps. The discrete element method uses a circular disk to represent the granular solid mass and their interactions are described by the Newton's third law of motion. The displacement is described by the sliding of the circular disk. This work is focused on the modeling efficiency of the discrete element methods to represent the behaviour of mine dump masses with the specified joint plane for the limit equilibrium method. The advantage of the work lies on the ease of information retrieval at any point at the dump mass concerning the stress and strain histories, displacement, failures etc. which when integrated produces a better understanding of the stability of the dump masses.     

GCr15轴承钢连铸过程中热物性参数的研究

借鉴前人实验数据,采用一定的数学方法,对轴承钢的热物性参数进行了研究.结果表明：GCr15轴承钢的液相线温度为1 465.7℃,固相线温度为1 328.4℃,零强度温度为1 380℃左右,零塑性温度为1 330℃左右;在固相区、液固两相区、液相区分别采用不同的公式进行处理,可使结果更加准确,还避免了奇异性.研究结果可为轴承钢连铸工艺有限元模拟提供基础.