飞机腐蚀搭接板的应力分析

为降低由于铝合金腐蚀产生的膨胀作用引起的枕垫效应对飞机搭接板应力的影响,利用非线性有限元法分别对不同铆钉弹性模量、不同搭接板弹性模量和不同搭接板泊松比下的腐蚀搭接板进行仿真分析.结果表明：枕垫效应对搭接板应力的影响随着铆钉弹性模量的增大、搭接板弹性模量和泊松比的减小而减小.     

BP神经网络在铝电解槽温度测量中的研究

针对铝电解槽温度高、腐蚀性强、温度难以直接连续测量的问题,引用BP神经网络技术,选择铝电解槽的输入电流、电压和下料速度作为辅助变量,建立BP神经网络模型,并利用matlab对数据样本进行了标准化处理,实现了BP神经网络的建立、训练和仿真。在预焙阳极铝电解槽进行实验,通过预算温度与实际温度进行对比,结果证明了该方法的有效性。     

Surface tension calculation of the Sn–Ga–In ternary alloy

Surface tensions of the Sn–Ga–In ternary alloy are calculated from the surface tensions of the Sn–Ga, Ga–In and In–Sn sub-binary systems by using geometric models (the Kohler model and the Toop model), and a general solution model (the Chou model). The calculated results are in excellent agreement with the experimental data (except for the Kohler model), assuming an experimental accuracy of ±2.5%. At the same time, the surface tensions of the Sn–Ga–In ternary alloy at 773 K and their sub-binary systems are predicted on the basis of Butler’s equation, in combination with thermodynamic data, and different model parameters β$\beta$ equal to the ratio of the coordination number in the surface phase to that in the bulk phase. Different values of β$\beta$ have almost no influence on the surface tensions. The predicted results agree with the experimental data. Therefore, the resulting iso-surface tension curves for the Sn–Ga–In ternary alloy at 773 K, especially those calculated by using the Toop model, are reasonable.     

锌合金工件不合格电镀层的返镀

本文在实践的基础上对锌合金工件不合格镀层返镀和修复提出了自己的看法，提供了化学退镀和电解退镀等方面的修复经验。     

6063铝合金型材氧化过程中出现"白斑"的原因分析及解决

分析了6063型铝型金在硫酸阳极氧化过程中出现“白斑”的原因并提出了解决措施。     

添加剂和亚磷酸对Ni^2＋,Fe^2＋电化学行为的影响

在Ｎｉ－Ｆｅ－Ｐ非晶态合金电镀工艺研究中，采用循环伏安法研究了某些有机酸和亚磷酸对Ｎｉ２＋、Ｆｅ２＋在铂电极上的电化学行为的影响。结果认为，甘氨酸、抗坏血酸和丁二酸等均能不同程度地增大Ｎｉ２＋、Ｆｅ２＋的阴极极化，亚磷酸能促进Ｎｉ２＋的还原析出，但阻止Ｆｅ的成核和生长过程。     

锡盐着色膜颜色与氧化膜中Sn含量的关系

对锡盐电解着色膜的颜色深浅与氧化膜中Ｓｎ含量两者之间的关系进行了研究。此外还探讨了锡盐电解着色液中镍离子和亚铁离子在电解着色过程中所起的作用。     

二次发射体MgO薄膜的俄歇电子能谱的研究

本文叙述了用PHI—550型给定的俄歇电子能谱(AES)研究了一种新的、性能优异的二次电子发射材料——MgO薄膜。薄膜由Ag—Mg合金经特殊高温激活工艺处理而成。以前人们对这种薄膜内部的各种元素的化学状态以及纵向原子浓度的分布状态一直不太清楚,本实验的成功证明了俄歇(Auger)电子能谱是研究这种薄膜的一种非常合适的实验方法。从实验结果中,我们发现如下几点 1.激活后,Mg和O原子的化学状态发生了显著的变化。 2.激活后,Mg、O和Ag原子的纵深分布也发生了显著的变化。 3.Mg原子氧化不充分,为了改进这一缺点,我们发明了一种新工艺。 4.使用新工艺激活,Mg原子可获充分氧化。     

Preliminary study on some properties of Co-Cr dental alloy formed by selective laser melting technique

The surface condition, some properties and ion releasing behavior of cobalt-chromium (Co-Cr) dental alloy formed by selective laser melting (SLM) technique were investigated. Before porcelain fused firing, the surface condition of the Co-Cr alloy was observed using a scanning electron microscope (SEM), and then the density and hardness were examined. After porcelain fused firing, the interface of porcelain and alloy was observed, and then the metal-ion release of the samples was tested. SLM technique provides Co-Cr alloy higher hardness than casting method. After degassing-oxidation procedure and porcelain fused firing, the interface of the alloy and porcelain showed excellent combination. Co ion was more than Cr ion released from SLM Co-Cr alloy, the amounts of Co and Cr ions were safe according to ISO security criterion. Considering the properties before and after porcelain fused sintering process, SLM technique is suitable for dental Co-Cr alloy restoration.     

一种原位TiB_2颗粒增强铝基复合材料的制备及特性

以Al-6Cu-0.2Mg-1Mn合金为基体,采用混合盐原位反应法制备不同TiB2颗粒含量（质量分数分别为1%、3%、5%）的颗粒增强铝基复合材料,对不同处理状态的TiB2颗粒增强复合材料及Al-6Cu-0.2Mg-1Mn合金的相结构与显微组织进行分析,并测试其维氏硬度。结果表明,原位反应生成的TiB2颗粒能改善基体组织,阻止基体晶粒生长的方向性,得到等轴晶;随着增强相TiB2颗粒含量的增加,基体组织得到明显细化;不同处理状态3%及5%含量TiB2颗粒增强复合材料的维氏硬度均显著高于相应Al-6Cu-0.2Mg-1Mn合金的维氏硬度。