Influence of nano-scaled dispersed second phase on substructure of deformed dispersion strengthened copper alloy

The deformation behavior of dispersion strengthened copper alloy Cu-Al2O3 was studied by TEM. The results show that nano-scaled dispersed second phase not only increases dislocation density in matrix, but also has an important influence on the dislocation substructure. The presence of fine dispersed Al2 O3 particles results in a uniform and random dislocation distribution in matrix copper and causes the difficulty in formation of dislocation cell structure and the decrease in the amount of cell structure during deformation. Deformation gives rise to much more dislocations and dislocation cells form more difficultly and the decrease in the cell size with the increase of dispersion degree.     

Preparation of Plate Fe_(60)Co_8Zr_(10)Mo_5W_2B_(15) Bulk Amorphous Alloy and Its Fracture Toughness

1Introduction Duwez[1]synthesizedthefoilAu Siamorphousalloyforthefirsttimewithrapidsolidification,whichinitiatedthepreparationofamorphousalloysintheprocessofalloysolidification,andthereaftertheresearchonamorphousal loysdevelopedrapidly.Since1980s,withthec…     

Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

论剪切质量的提高

通过对飞剪剪切长度，精度，剪刃间隙和压板机构等参数的优化，来提高钢板的剪切质量。     

Effects of thermal and mechanical treatments on a titanium-based conversion coating for aluminium alloys

The influence of mechanical deformation and heating on the protective performance of a chromium-free conversion treatment for aluminium alloys has been assessed by polarisation and AC impedance measurements. Protection is unlikely to be seriously compromised by typical production operations.     

NOPD技术在板结构声辐射控制中的实验研究

本文应用NOPD技术设计了一种复合多层板，按照四边固定薄板结构的模态振型，对不同的NOPD填充形式，进行声学实验，来评价不同填充形式在降低板类结构声辐射方面的效果，分析了该类板结构声振耦合的关系并验证了NOPD技术对声辐射控制的作用。     

裂齿矩形翅片板翅式换热器优化设计的分析

对裂齿矩形翅片板翅式换热器中的裂齿矩形翅片的传热效率作了分析,并以单位质量材耗的换热能力最大为目标函数,分析研究了在不同雷诺数(Re)的操作条件下裂齿矩形翅片间角度、翅片厚、长度、宽度及极厚之间的关系。结果表明:在气体换热的场合下,当Re在某一范围时翅片可有效地起到强化传热的作用。当板厚为5mm,翅片厚为3mm,翅片间夹角为45°～70°,Re为2×10~3～8×10~3,最佳翅片纵向间距与翅片长度和翅片厚度乘积的平方根的比为1.5～2.5,最佳翅片尺寸系数为3～5时,传热强化效果较好。     

12．5×10^4 m3储油罐底板阴极保护方案比选

对国内外储油罐底板内外侧各种阴极保护方法进行了分析对比。重点介绍了茂名分公司12.5×10~4m~3储油罐底板内外侧阴极保护方案:内侧为涂料加铝合金牺牲阳极阴极保护;外侧为涂料加混合金属氢化物网状阳极阴极保护。     

RMT1-250转换开关用电接触材料

铜铬锆合金是一种形变热处理材料，兼具了铜铬合金和铜锆合金的各种优良性能，经过时效处理的铜铬锆合金，与铜相比，高温强度有很大的改善，而且具有较高的导电率。所以铜铬锆合金广泛应用于电焊机、低压电器等行业。根据对铜铬锆成分的适当调整，可用作为电焊机电极，低压电器触桥、短路环等各种电接触材料。铜铬锆合金用于RMT1－250转换开关，接近于触桥材料的应用，但使用的条件更苛刻一些，要承受部分电弧的侵蚀和由此产生的高温，因此对材料要求具有良好的导电导热性和更高的高温强度。     

钛制设备在焦化行业中的应用

介绍焦化行业钛设备的应用,剖析了分块式钛泡罩塔盘的结构特点,并对其经济性作了分析。