中铝河南分公司矿山在土地复垦中的有益探索

分析了铝土矿露天开采和土地、环境之间的利害关系，并对矿山公司“土地复垦”工艺技术进行了阐述，介绍了中铝河南分公司矿山公司方面的具体作法和成功经验。     

S-N-P curves in 7075 T7351 and 2024 T3 aluminium alloys subjected to surface treatments

The S-N-P (stress, number of cycles, failure probability) curves for 2024 T3 and 7075 T7351 aluminium alloys were obtained. Previously, surface treatments of degreasing and different types of anodizing were applied to samples, evaluating the influence of these treatments on the fatigue life of the alloys. The determination of the S-N-P curves was done using Maennig's method. Rotary fatigue was used because this technique produces greater stress on the sample surfaces, the zone in which it is important to evaluate fatigue resistance. Both the transition range and the finite life range were evaluated, calculating the 1, 50 and 99% fracture probability. SEM was performed in order to characterize the fracture micromechanism. The conclusions were that Maennig's method is useful to evaluate fatigue life of these materials in a fast and efficient manner. Moreover, surface treatments produce a decrease in the fatigue life of both alloys, associating this effect with the surface damage produced on each sample during the treatment.     

Failure analysis of a hot extrusion die used for Al-Li alloy processing

Al-Li alloys being developed as lighter, substitutes for conventional high strength Al alloys are to be processed by routine methods. During extrusion of a 8090 Al-Li alloy, the extrusion die container failed causing some alarm. This failed die container was analysed to examine if the failure was caused by interaction of Li diffusing out of Al-Li alloy with the carbides of die steel. The evidence, although not conclusive, is sufficient to exercise caution during such processing.     

A numerical model for the dissolution of spherical particles in binary alloys under mixed mode control

A general numerical model is described for the dissolution kinetics of spherical particles in binary systems for any combination of first order reactions at the particle-matrix interface and long distance diffusion within the matrix. The model is applicable to both finite and infinite media and handles both complete and partial particle dissolution. It is shown that interfacial reactions can have a strong effect on the dissolution kinetics, the solute concentration at the particle-matrix interface and the solute concentration profile in the matrix.     

Peculiarities of erosion-corrosion processes

Investigations have been carried out on an erosion-corrosion apparatus to investigate the behaviour of corrosion-resistant highalloy iron-base materials containing hard phases. These materials had been optimized for increased wear resistance under complex stress conditions. As expected, in dry erosion tests, very low mass losses were established; there was little difference between the materials. Also, in corrosive environments (NaCl, H₂SO₄), the materials showed good stability; however, the duplex structures were superior to the martensitic ones. The combination of erosion and corrosion produced large differences and, in some cases, markedly reduced resistance to damage. These results confirmed observations that it is impossible to deduce the environmentally influenced mechanical behaviour of an alloy from its behaviour in separate corrosion and erosion experiments. The basic mechanisms underlying these processes have been investigated only tentatively.     

浅议铝箔项目的给排水设计

通过铝箔项目的工程实例,详细介绍了铝箔项目给排水专业设计的主要构成,并总结了几点设计体会,可供有关专业设计人员借鉴、参考。     

升深2-17井络合铝聚合物充气钻井液现场试验

为加快徐加固子深层天然气的勘探开发步伐，缩短深层气井的建井周期，在升深2-17井进行了充气钻井试验。介绍了络合铝聚合物充气钻井液技术的现场应用概况及效果以及井漏的发生与处理过程、钻井液起泡的解决措施。在现场试验过程中，络合铝聚合物钻井液性能稳定，具有较强的抑制性和较好的流变性能，流性指数控制在0．7左右，具有良好的携屑和稳定井壁能力，而且粘度较低，基本上控制在33～52s之间，满足了现场充气和脱气的需要；该钻井液抗温可达180℃，润滑性能较好，在钻井过程中无粘卡显示，在深井欠平衡井眼稳定方面取得了较好的效果；在不同的气液比条件下，可以在0．83～1．08g／cm。之间实现对当量密度的调节;与常规钻井工艺相比，充气钻井可以使机械钻速提高30％～50％；在钻进过程中实现了充气和点火同时进行，达到了欠平衡钻井工艺技术的要求，为进一步开展气体钻井打下了良好的基础。     

Hybrid gas-to-particle conversion and chemical vapor deposition for the production of porous alumina films

Porous alumina films can be found in a wide variety of materials, including filters, thermal insulation components, dielectrics, biomedical and catalyst supports, coatings and adsorbents. Production methods for these films are as equally diverse as their applications. In this work, a hybrid process based upon chemical vapor deposition and gas-to-particle conversion is presented as an alternative technique for producing porous alumina films, with the main advantages of solvent-free, low substrate-temperature operation. In this process, nanoparticles were produced in the vapor phase by reaction of aluminum acetylacetonate in the presence of oxygen. Downstream of this reaction zone, these nanoparticles were collected via thermophoresis onto a cooled substrate, forming a porous film. Some deposited films were subjected to post-processing in the form of annealing in air. Fourier-transform infrared spectra and X-ray energy-dispersive spectroscopy analysis confirmed the production of alumina at processing temperatures above 973 K. X-Ray diffraction revealed that the films were amorphous. Film thickness, ranging from 30 to 250 μm, and the average deposition rate were determined from scanning electron microscopy results. From transmission electron microscopy, the average primary particle size was determined to be approximately 18 nm and the formation of nanoparticle aggregates was evident. Annealing of the films at temperatures ranging from 523 to 1173 K in the presence of air did not have an effect on particle size. The specific surface area of the powder composing the films ranged from 10 to 185 m² g⁻¹, as determined from nitrogen gas adsorption by the Brunauer–Emmett–Teller method.