钽及钽合金在工业装备中的应用

针对钽与钢之间因物化性能差异大,储能焊接头易产生脆性金属间化合物等问题,依据熔核金属高熵化技术思路,以等摩尔比的Ta₂₀Fe₂₀Ni₂₀Cr₂₀Cu₂₀合金为熔核目标成分,依据焊接过程两种母材熔合比折合得到Ta₈Ni₃₀Cr₂₀Cu₄₂中间层合金,将其用于Ta1/0Cr18Ni9的储能焊连接. 结果表明,熔核金属的高熵合金化可有效地抑制熔核中脆性金属间化合物的形成,Ta1/Ta₈Ni₃₀Cr₂₀Cu₄₂/0Cr18Ni9储能焊接头形貌完整,熔核呈规则的杯形,长径约0.6 mm,整体向钢侧发生了偏移. 熔核组织以简单FCC固溶体为主相,兼有少量BCC固溶体. 熔核中心凝固组织以细小的等轴晶为特征,熔核与两侧母材熔合区则形成了平行生长的柱状晶,熔核区与母材结合良好. 在焊接电压1 000 V,电容500 μF,电极力30 N工艺条件下,接头平均抗剪强度372 MPa.     

Nanoindentation and scratch behaviour of Ni–P electroless coatings

ABSTRACT

In the present paper, the mechanical properties and the scratch failure mechanisms of Ni–P electroless coatings are described. The material microstructure was studied in as-deposited and annealed conditions through SEM and EDS analyses. Nanoindentation measurements on the coatings showed a remarkable hardening due to the crystallization and precipitation behaviour produced by annealing. The scratch tests, conducted by increasing the load during scratch, revealed the coating failure mechanisms in a broad range of applied stresses up to delamination.     

00Cr17Ni14Mo2不锈钢的性能及应用研究

研究了00Crl7Nil4M02不锈钢材料的机械性能、焊接性能和耐腐蚀性能，从用户和研究开发的角度探讨了其在压力容器、化工装置、化肥装置、海洋装置和建筑业等领域的应用。     

The Influence of High Temperature Exposure on the Wear Performance of a Ni Based Alloy PTA Coating

Degradation phenomena like wear and corrosion, may have their effects accelerated as components operate at high temperature. The aim of this work is to make an indirect evaluation of the influence of high temperature exposure on wear behavior of Ni coatings. A Ni-Cr-Mo-W alloy, was deposited with Plasma Transferred Arc (PTA) process. An indirect approach based on the Ahrrenius relationship was used to evaluated long time exposures at high temperatures. To simulate longer exposures at lower temperatures, coatings were exposed to higher temperatures for the same time interval. So coatings were soaked in an air furnace at 650℃, 1000℃ and 1200℃. Metal/metal wear behavior was evaluated by pin-on-disc tests. Pins were removed from the coatings by eletrodischarge machining and rubbed against a VC31 quenched and tempered tool steel. Two sets of wear tests were run at 2m/s, for different loads (0.5, 1.0, 2.0 and 3.0Kg) and for different sliding distances (120, 720, 1080, 1440 and 1800m).Coatings characterization was done by scanning electronic microscopy and Vickers microhardness. Results showed as temperature is increased, coatings wear performance is altered,and this is associated with microstructural changes.     

Antibacterial Property of Martensitic Stainless Steel Generated by Cu Ion Implantation

ION IMPLANTATION is a promising techniquepermitting of the surface properties improvement formetal materials.It had used in many industrydepartments,especially,it was used for the successfulsolution of many problems associated with hardness,wear and corrosion of metal surface[1-4].Howeverresearch on antibacterial stainless steel by copper ionimplantation method has not been reported till now.In this study,we report a special antibacterialtreatment after copper ions implantation intomarte…     

Ni/Al Intermetallics Plasma Transferred Arc Processing

TAILORING COMPONENT SUFACES for elevatedtemperature operations has been a goal of researchersduring the last century.Process and material selectionare the key factors for this development.In particularlythe latter can be described to have started with thedevelopment of stainless steels.Ni and Co based alloys,the superalloys,attended the increasing technologicaldemands for higher service temperatures(1).Morerecently the higher operating temperatures ofequipments,such as gas turbines,r…     

NH_3 Plasma Surface Treatments of Engineering Fluoropolymers: A Way to Enhance Adhesion of Ni or Cu Thin Films Deposited by Electroless Plating

FLUOROPOLYMERS(FPs)are thermoplasticmaterials which exhibit a number of unique chemicaland physical characteristics that no other man-madeplastic product gets together.For example,FPs showvery good resistance to almost all chemicals,excellentwater vapor barrier properties,high thermal stability,outstanding electrical insulation properties(lowdielectric constant and dissipation factors),extremelylow frictional coefficient giving them high auto-lubrication properties,high resistance to rad…     

Hydriding-dehydriding properties of Mg2Ni alloy modified by ball-milling in tetrahydrofuran

A new approach of ball-milled Mg2Ni in tetrahydrofuran (THF) to improve the hydriding kinetics of Mg2Ni alloy is suggested and studied. It is found that the modified alloy displayed the improved activity for hydriding even at relatively low temperature (e.g., 323-373 K). In the case of the sample milled in THF for 20 h, the hydrogen content (mass fraction) reaches 1.6 % at 323 K, 2.1% at 348 K and 3.4% at 448 K, respectively. The use of THF during grinding led to the change of the structure, which is reflected by the broadening and weakening of the diffraction peaks in the XRD spectra. The XPS analysis shows that Mg (2s) binding energy peak of Mg2Ni after modification shifted from a lower binding energy to a higher one, indicating the charge transference between Mg and THF and the formation of catalytically active electron donor-acceptor (EDA) complexes on the surface of modified Mg2Ni alloy.     

Crystallization and microstructure evolution of amorphous Al85Y4Nd4Ni7 alloy

The mixture model of Al85Y4Nd4Ni7 alloy in which a partially crystallized amorphous alloy is regarded as a nanocomposite of an Al nanoparticle and a remaining amorphous matrix is presented. Its evolution in the process of crystallization has been investigated by differential scanning calorimetry (DSC), X-ray diffraction (XRD), and transmission electron microscopy (TEM). Mainly amorphous structure with α-Al nanocrystals embedded in the amorphous matrix has been revealed by melt spining the alloy. Crystallization is showed to occur in three stages: (I) crystallization of amorphous alloy and formation of A1NiY, A1NdNi and unknown crystalline phases, (2) formation of Al3Y and Al3Nd, and (3) formation of Al3Ni.