圆盘锯机性能提升途径

圆盘锯机在线材厂投入使用时不能满足生产的需要：锯切周期太长，锯片使用性能差，经过对设备进行技术改造和对设备操作规程进行优化，以及在操作上加强管理，使之关键指标大幅度提升，为圆盘锯机的使用改善提供了新的思路。     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Triple tangent flank milling of ruled surfaces

This paper presents a positioning strategy for flank milling ruled surfaces. It is a modification of a positioning method developed by Bedi et al. [Comput Aided Des 35 (2003) 293]. A cylindrical cutting tool is initially positioned tangential to the two boundary curves on a ruled surface. Optimization is used to move these tangential points to different curves on the ruled surface to reduce the error. A second optimization step is used to additionally make the tool tangent to a rule line, further reducing the error and resulting in a tool position, where the tool is positioned tangential to two guiding rails and one rule line. The resulting surface has 88% less under cutting than the method of Bedi et al.     

氧化铝熟料单筒冷却机节能技术改造

本对影响氧化铝熟料单筒冷却机冷却效率的因素进行了分析，并提出了相应的节能技术改造措施，取得了明显的节能效益。     

AHMED experiments on hygroscopic and inert aerosol behaviour in LWR containment conditions: experimental results

Hygroscopic NaOH, CsI, CsOH and inert Ag aerosol behaviour at different temperatures and relative humidities (RH) has been studied in a well instrumented and controlled vessel of 1.81 m³ total free volume. Homogeneous thermal-hydraulic conditions for aerosol measurement in the vessel were achieved. The aerosol number and mass concentration were measured continuously during the experiments using a Condensation Nucleus Counter and a Tapered Element Oscillating Microbalance. The particle size distribution and chemical composition in the test conditions were measured by Berner low pressure impactors. In the case of NaOH the half life of the aerosol mass concentration was more than four times longer at low RH (22%) as compared to high RH (96%). The half lives of the CsOH and CsI aerosols were only twice as long at low RH as compared to high RH. Thus at high RH (96–97%) the half lives of CsOH and CsI were twice as long as the half life for the NaOH aerosol. The faster decay of the NaOH aerosol is due to the smaller density decrease of NaOH during water condensation. CsOH particles grew rapidly to their equilibrium size at all humidities. The measured equilibrium size for CsOH aerosol agree well with the calculated particle size at different RHs. Experimental results were also compared with calculations obtained by severe accident computer codes. These calculated results will be presented in a later paper.     

直流电动机参数测定

根据直流电机的可逆原理并利用常规的实验仪表，可以简便、准确地测出直流电动机的主要参数－电磁转矩、输出转矩和效率．     

机械合金化的原理及在磁性材料研究中的应用

介绍了机械合金化的原理和描述机械合金化过程的理论模型。综述了机械合金化在磁性材料研究中的应用，并对目前研究中的存在的问题及发展前景进行了分析。     

某微型起爆器引起的一起误爆事故分析

该文分析某微型起爆器引起的一起误爆事故，指出该起爆器设计上的缺陷及其对作业安全的威胁，提出防患建议。     

MKR──一种有效的增量式概念获取系统

本文对示例式学习的ＩＤ５Ｒ算法进行了深入的研究并作了进一步的改进，提高了其计算效率．并提出一种适合于增量式学习的抗干扰机制，拓广了算法的适用范围．     

Real-World Robotics: Learning to Plan for Robust Execution

In executing classical plans in the real world, small discrepancies between a planner's internal representations and the real world are unavoidable. These can conspire to cause real-world failures even though the planner is sound and, therefore, proves that a sequence of actions achieves the goal. Permissive planning, a machine learning extension to classical planning, is one response to this difficulty. This paper describes the permissive planning approach and presents GRASPER, a permissive planning robotic system that learns to robustly pick up novel objects.