Evolution of chemistry and morphology during the carbonization and combustion of rice husk

Both fine carbon/silica and pure silica powders can be obtained by carbonization and combustion of rice husk under non-isothermal conditions, and the products can be used for preparation of high-quality ceramic materials. Studies on the morphology, chemical and physical characteristics of products were carried out by N₂-adsorptionmeter, SEM, XRD, FTIR, ICP-MS and EA. Results indicate that decreasing the heating rate increased the specific surface area, pore volume and pore diameter. At a heating rate of 5 °C/min, the specific surface areas of both the carbon/silica and pure silica powders were 261 and 235 m²/g, and the average pore diameters were 2.2 and 5.4 nm, respectively. The products obtained from various heating rates were all amorphous. Thermogravimetric analysis was employed to study the reaction characteristics during carbonization or combustion, indicating that decomposition process of rice husk could be divided into three temperature zones. This results of the study can also provide the important information on the recovery of biomass material from rice husk.     

Simulation of carbon nanotube based p-n junction diodes

Taking advantage of the unique characteristics of an ambipolar carbon nanotube field effect transistor (CNTFET), a ‘p-n junction’ is simulated along the single-walled carbon nanotube channel using two separate gates close to the source and drain of the CNTFET, respectively. The current-voltage characteristics of the double-gated CNTFET are calculated using a semiclassical method based on the Schottky barrier field effect transistor mechanism. The calculation results show a good rectification performance of the p-n junction.     

Important issues in a molecular dynamics simulation for characterising the mechanical properties of carbon nanotubes

This paper discusses several important issues in a molecular dynamics simulation for analysing carbon nanotubes and their mechanical properties. In particular, the paper addresses the problems in selecting appropriate inter-atomic potentials, number of thermostat atoms, thermostat techniques, time and displacement steps and number of relaxation steps to reach the dynamic equilibrium. Based on these, the structural changes of armchair and zigzag nanotubes and their mechanical properties are investigated. The Young's modulus and Poisson's ratio of the armchair tube are 3.96 and 0.15 TPa, respectively, and those of the zigzag tube are 4.88 and 0.19 TPa, respectively. The best simulation technique identified in this study predicts that the ultimate tensile strain of a carbon nanotube is around 40% before atomic bond breakage.     

A growth mark method for studying growth mechanism of carbon nanotube arrays

A novel and simple growth mark method was developed to make marks during the growth process of carbon nanotube arrays. These marks can be read out under scanning electron microscope or optical microscope. Based on this method, the growth rates at different temperatures and under different acetylene partial pressures were measured, from which the activation energy and the order of reaction were determined. Based on our experimental results, the growth of carbon nanotube arrays in our experimental condition could not be diffusion-limited. The measured activation energy could possibly be attributed to the heterogeneous decomposition of acetylene over the catalyst particle. Furthermore the marked array with special segmental structure may be found some applications in the future.     

Preparation of highly crystalline nanofibers on Fe and Fe-Ni catalysts with a variety of graphene plane alignments

The present study confirmed that highly crystalline nanofibers with controlled structure may be prepared over Fe and Fe-Ni alloy catalysts. The degree of graphitization of various carbon nanofibers (CNFs) was analyzed by using C(0 0 2) peaks from the XRD profiles. The C(0 0 2) peaks of CNFs over Fe catalyst shifted to higher angle and became narrower as the preparation temperature increased from 560 to 620 °C. Tubular CNFs prepared at temperature higher than 630 °C showed lower 2θ angles compared to those of platelet fibers. CNFs prepared over Fe-Ni catalysts tended to resemble those prepared over Fe catalysts. The degree of graphitization of platelet CNFs resembled natural graphite, while d_0 0 2 of the tubular CNFs showed values below the 3.39 Å reported as a theoretical minimum for a cylindrical alignment. Lc_0 0 2 of platelet and tubular CNFs increased by heat treatment at 2000 and 2800 °C though d_0 0 2 changed little. A transverse section of platelet and tubular CNFs had a hexagonal shape, not a round shape. The hexagonal column allows AB stacking of hexagonal planes that can give perfect hexagonal alignment.     

Polybrominated Diphenyl Ethers in Surface Sediment from Songhua River Basin, Northeast of China

Sixty sediment samples were collected from the main Songhua River in three years. Twelve polybrominated diphenyl ether ( PBDE) congeners ( BDE17, 28, 47, 66, 99, 100, 153, 154, 138, 183, and BDE?209) w...     

数控车床振动的控制Ⅰ:振源与力学模型

本文论述了数控车床的振源，建立了三种力学模型，并进行了分析，为数控机床的数学模型的建立和振动的控制打下了基础。     

ZL114铝合金激光--龟弧的复合焊接

设计了一种激光-电弧复合热源焊接ZL114合金的新工艺，并对焊后的试件进行了X光检测、抗拉强度和全相组织等实验。结果表明，该种新工艺对铝合全有良好的适应性和可行性，是焊接领域的一个趋势。     

TEM IMAGING TECHNIQUE

This imaging technique is used for approximate interpretation of TEM data including ungrounded loopsource and grounded line source soundings.Loop source data can be collected as central-loop soundings or asout-of-loop soundings with a short or long offset configuration.The imaging method is based on the same princi-ple as that employed by Fullager(1989),with apparent resistivities computed directly from time-derivative data,db/d,and then associated with depths according to image theory.     

逆变电源的可靠性及其提高途径

影响逆变焊接电源可靠性的因素是多方面的.如产品的设计和生产等各个环节.根据实践经验提出了解决可靠性问题的一些有效途径和方法.