Delamination Analysis for Laminated Composites. II: Numerical Verification

A validation of the delamination analysis models developed in a companion paper is provided through comparisons of predictions with finite‐element and elasticity solutions. The models are applied to the analysis of composite compression specimens reinforced with end tabs. An elasticity solution for the gage section of the specimens is developed. A comparison of the characteristic roots shows that the predictions of the models include the material and geometric parameters that control the behavior, and the roots corresponding to the basic stretching and bending modes are accurately predicted. The stress distribution at the interface between tabs and specimen is in good agreement with a finite‐element simulation. The interlaminar shear and peel stresses show an exponential increase with a maximum intensity at the free edges of the tabs. The behavior of previously tested specimens is explained; and practical guidelines for specimen design are provided to avoid unwanted extraneous modes of failure. The influence of the deformation modes associated with each model is investigated. An assessment of the accuracy and level of complexity is presented.     

Pressureless sintering and characterization of cordierite/ZrO2 composites

Cordierite/ZrO₂ composites with 5 to 25 wt% ZrO₂ were fabricated by conventional powder mixing and pressureless sintering method. Their densification behavior, microstructure, mechanical and thermal properties were studied. By dispersing 25 wt% (9.57 vol%) ZrO₂, densified cordierite/ZrO₂ composite with a relative density of 98.5% was obtained at an optimum sintering condition of 1440 °C and 2 h. ZrO₂ particles were homogenously dispersed within matrix grains and at the grain boundaries. The intragranular particles were finer than 100 nm and the intergranular particles were coarser. Both fracture strength and toughness could be enhanced more than two times higher, compare to those of monolithic cordierite, by dispersing 25 wt% ZrO₂ into the cordierite matrix. The toughening mechanism in the present composites was mainly attributed to martensitic transformation due to ZrO₂ dispersion. Electronic Publication     

Magnetic properties of nickel filament polymer-matrix composites

The magnetic properties of polyethersulfone-matrix composites with 3-19 vol.% polycrystalline nickel filaments (0.4 (im diam) were investigated. These filaments were found to exhibit hysteresis energy loss 10800 J/m³ of nickel and coercive force 16.9 kA/m, compared to corresponding values of 4930 J/m³ and 4.7 kA/m for 2 μ.m diam polycrystalline nickel fibers, 1020 J/m³ and 0.5 kA/m for 20 μm diam polycrystalline nickel fibers, and 1280 J/m³ and 2.3 kA/m for solid polycrystalline nickel.     

Radiation transmission through a composite pure water layer of uniform and depth-dependent extinction characteristics

The paper describes the calculation of the beam solar radiation transmission across the uniform salinity upper convecting zone (UCZ) and the salinity stratified gradient zone (GZ), when the extinction coefficient is not only wavelength but also salinity-concentration dependent, assuming that the effect of scattering to be negligible. The results are useful in determining the effects of dissolved salt ions on pure water transmission, at least according to the existing measured data in the literature.     

丁腈橡胶/导电粒子复合材料的正温度系数(PTC)特性

将导电粒子碳黑和铜粉分别与丁腈橡胶混合制备导电聚合物复合材料，其中碳黑（Ｎ５５０）／丁腈橡胶复合材料的电阻率随温度的变化呈现较强的正温度系数（ＰＴＣ）效应。讨论了掺入导电粒子浓度、结构和表面性质以及混炼硫化工艺等对该类材料的室温电阻率及ＰＴＣ效应的影响。     

Rich photoluminescence emission of SnO2–SiO2 composite aerogels prepared with a co-fed precursor sol–gel process

Tin oxide–silica composite aerogels were successfully prepared with a co-fed precursor sol–gel process. The crystallinity of the tin oxide nanoparticles, embedded in the mesoporous SiO₂ network, was improved with increasing the post-reaction thermal treatment temperature. The composite aerogels exhibited a rich photoluminescence (PL) emission contributed by both SnO₂ and SiO₂. The PL peak of 346 nm was from the near band edge emission of the tin oxide nanoparticles, and the ones located at 310 and 476 nm were attributable to the oxygen deficiencies of the silica network. Three more emission peaks, 387, 432, and 522 nm, were observed, with the 387 nm peak contributed by the oxygen vacancies V_O⁺⁺, the 432 nm peak by the Sn interstitials, and the 522 nm peak by the oxygen vacancies V_O⁺, respectively, of the tin oxide nanoparticles. The intensities of these three defect level emissions were found decreased, as compared to that of the near band edge emission, with increasing the post-reaction thermal treatment temperature as the tin oxide crystallinity improved.     

A micromechanics model for the prediction of static strength of off-axis unidirectional laminates

In this paper a micromechanics model using the concentric cylinder assemblage model and the Mori-Tanaka average stress scheme is used to predict the static strength of unidirectional angle ply laminates. The predicted strengths agree with experimental results for Glass/Epoxy and Graphite/Epoxy systems.     

A novel design in composities of various materials for solar selective coatings

This study describes the development of multilayer metal-dielectric graded index solar selective coatings in which the metallic volume fraction increases with depth, from top (air–film interface) to bottom (film–substrate interface). The work is based on computer simulation followed by validation through fabrication of the coatings and optical measurements. The influence of the choice of the number of layers present in a graded index composite selective absorber and results obtained for a new destructive interference bilayer (four-layer system) coating, designed using the computer model, were studied. The design and optimization of the composite coating was undertaken using a computer tool developed within this program of research employing Bruggeman and Maxwell–Garnett effective medium formalisms. The design tool enabled all key design parameters, with the exception of particle size and orientation, to be varied systematically to permit the sensitivity of the optical properties of the selective absorber coating to be studied.The model was validated with a supporting program of experimental research in which many different selective absorbers were prepared by co-sputtering of metal and dielectric materials.Although the best compositional gradation can be achieved by increasing the number of layers, the variation in optical performance beyond a certain number of layers is minimal. The destructive interference produced between adjacent layers contributes to the absorptance. The effect of the number of layers (single, four and 10) has been calculated for various materials such as nickel, vanadium, tungsten, cobalt and chromium based coatings. Solar absorptance of 0.98 and 0.96 was achieved by simulation and experimental findings with less than 0.07 thermal emittance at 300 K for 200 nm thick, 4-PGSAC (four-layer system) of V : Al₂O₃ composites. Other designs showed lower optical performance for all the material combinations regardless of their individual optical properties. Use of such thin film coating on the absorbers of solar thermal appliances can reduce thermal losses significantly, which could be of importance to the relevant industry.     

复合射孔枪枪身材料动态本构关系的试验研究

为确定复合射孔枪枪身材料32CrMo4钢在井下高温、高加载率工作环境下的动态性能,利用MTS试验机和分离式Hopkinson冲击压杆装置做了应变率为0.001、1000和3000/s,温度为294、373、473和573K的单轴动态压缩试验,得到32CrMo4钢各组温度及应变率下的流动应力-应变曲线。拟合得到该钢Johnson-Cook本构关系模型所需的5个参数,模型拟合曲线与试验曲线吻合。     

发射药包装用复合纸桶现状与国内外纸桶对比

火炸药是易燃、易爆的产品，所以，它对包装要求也是很高的，特别强调它的包装可靠性。近几年来发展上许多国家都采用复合纸桶包装发射药，我厂生产的复合纸要能与国内外纤维板圆桶对比，在技术质量方面都比较先进。