溅射靶材的应用及制备初探

随着电子及信息产业突飞猛进的发展，世界溅射靶材的需求越来越多，本文介绍了靶材的发展概况、分类和应用情况，以及靶材的特性要求．探讨Ni-Cr合金靶材的制备工艺，结果表明，产品能满足靶材特性要求。     

Delamination Analysis for Laminated Composites. II: Numerical Verification

A validation of the delamination analysis models developed in a companion paper is provided through comparisons of predictions with finite‐element and elasticity solutions. The models are applied to the analysis of composite compression specimens reinforced with end tabs. An elasticity solution for the gage section of the specimens is developed. A comparison of the characteristic roots shows that the predictions of the models include the material and geometric parameters that control the behavior, and the roots corresponding to the basic stretching and bending modes are accurately predicted. The stress distribution at the interface between tabs and specimen is in good agreement with a finite‐element simulation. The interlaminar shear and peel stresses show an exponential increase with a maximum intensity at the free edges of the tabs. The behavior of previously tested specimens is explained; and practical guidelines for specimen design are provided to avoid unwanted extraneous modes of failure. The influence of the deformation modes associated with each model is investigated. An assessment of the accuracy and level of complexity is presented.     

离子束混合工艺对材料抗蚀性能的影响

本文介绍了离子束混合工艺方法。与直接注入相比较,离子束混合所使用的设备造价低1/4—1/2,而生产效率可提高1—2个数量级,因而使生产成本大幅度降低,这无疑对离子束工艺的实际应用将产生巨大的促进作用。 通过对轴承材料(GCr15和Cr4Mo4V)经Cr、N、Ta不同元素的混合处理后,在0.5M H_2SO_4和0.1M NaCl的缓冲溶液中的阳极极化曲线表明经混合处理后的两种材料试样,其抗蚀能力和抗点蚀能力均大大提高,这与直接注入的试样效果是一致的。 通过俄歇谱仪和透射电镜的分析结果表明混合是成功的,且在一定的条件下,形成非晶组织。 本文的结论是,无论是离子的直接注入还是离子束混合,对提高轴承材料的抗腐蚀性能都是有效的方法,特别是离子束混合技术具有更大的应用前景。     

脆断事故的原因分析和预防措施

分析高强度材料和大型工程结构元件发生低应力脆性断裂的原因及条件，指出传统强度设计理论的局限性，从设计和工艺上提出防止发生低应力脆断事故的具体措施，给使用高强度材料和设计大型工程结构元件时提供参考。     

Hydrogen Absorption and Release Behavior in Hydrogen Decrepitation Process of Nd-Fe-B Alloys

The behavior of hydrogen absorption and release in hydrogen decrepitation (HD) process of Nd-Fe-B alloys were investigated. The results reveal that the reactivity and the amount of hydrogen absorption in HD process are related to the surface activity of the alloy so that the fresh and active surface has a higher efficiency. The presence of Nd-rich phase at the grain boundary is an essential factor of the HD activity of the alloy at room temperature. On degassing, hydrogen is released from the HD powder continuously with increasing temperature. And the residual hydrogen is as low as 0.0015% at 1073K, which shows that the hydrogen is almost exhaused. It is feasible to remove the hydrogen from the HD powder by heating treatment at the temperature of 523-723K for 1h prior to the magnetic field forming in order to decrease the harmful effect of hydrogen on the easy axis alignment of HD magnet.     

部分种子成分的特征X射线在等效生物材料中衰减的测定

用Ｓｉ（Ｌｉ）探测器实现了Ｎａ、Ｍｇ、Ｓ、Ｃｌ的特征Ｘ射线在有机膜中的相对衰减以及与Ｏ、Ｋ元素的特征Ｘ射线能量相当的Ｘ射线或轫致辐射在有机膜中的相对衰减，分别得出了它们减的数学描述，并把实验得到不同能量的Ｘ射线在有机膜中的质量吸收系数与Ｂｅｒｋｅｌｅｙ的ＯＣＧ软件计算出的结果相比，相关都小于３０％。     

近期全国建材市场走势展望

结合当前我国建材市场的形势 ,就建材市场“涨价风潮”的起因 ,从经济增长的结果、市场运行的规律等方面进行了论述 ,提出了涨价风潮对近期全国建材市场的影响     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

旋波媒质基本参数的一种测试方法

本文提出了直接利用旋波材料板的Ｓ参数获得其基本参数的方法。通过自由空间测量旋波材料板的反射场和透射场，可以反演得到媒质的复介电常数、复磁导率、旋波量以及透射场的轴比和旋转角，测试程序简单，结果精度高。     

世界高新材料技术发展的新趋势

本文根据90年代以来新材料技术的新进展,高度概括地评述了世界新材料技术发展的新趋势,以期对跟踪世界高新技术提供依据。