Investigation of Centreline Segregation and Centreline Porosity in CC ‐ Slabs

Improvements of solidification processing in conventional or near net shape casting depend on sophisticated methods of macroscopic examination of central unsoundness and inhomogeneity of the cast material. As long as remarkable deviations referring to the quality features exist between the slab centre and the bulk material such methods should be looked after. Two semi‐macroscopic methods of segregation analysis are discussed in this paper: firstly, the potential of the emission spectral analysis combined with sectioning of a sample and secondly, the computer aided micro‐probe analysis. Both methods are restricted to small local areas. The proneness of elements and steel grades with respect to micro‐ and macrosegregation as well as distribution‐ and segregation coefficients are determined. The effect of a diffusion anneal on homogenisation of segregation is studied. Last not least the precipitation of sulphides, phosphides or carbonitrides is estimated. Ultrasonic detection of the central unsoundness of conventional slabs or thin slabs is a new approach towards a quantitative macroscopic examination. The sample size is 400 mm x 300 mm x 30 mm. To achieve a low ultrasonic noise using a 5 MHz‐transducer the samples are heat treated for grain refinement. “Dog bone porosity”, macroscopic topographical misfit between the upper and lower solidifying shells, periodical corner cracks or systematic transverse centre cracks are detected. Obviously, segregations do not reflect the ultrasonic beam. However, it can be presumed that an interrelation exists between porosity and segregation, although these might be locally apart from each other. This new ultrasonic test of the central unsoundness of continuous cast (c.c.) slabs gives valuable arguments to machine builders and maintenance people to decide on the right concepts for strand guidance, support rollers and secondary cooling. Soft reduction can be optimized and variations in casting speed counteracted by dynamic means. R&D service of this kind can help steelmakers when decisions are impending to build new casting machines or revamp old ones.     

现代电弧炉流程钢液氮控制的试验研究

通过生产试验研究了电弧炉冶炼过程、LF精炼过程及连铸过程钢液氮的控制。研究表明，电弧炉冶炼过程主要是电弧区增氮，LF过程及连铸过程钢液增氮主要是钢液与大气接触，LF供电制度也对钢液吸氮有影响。     

合金钢连铸机生产工艺分析及实践

对新钢特殊钢有限责任公司整个合金钢连铸机的生产工艺进行了分析，提出了提高钢水质量和优化连铸工艺参数的有效措施，使铸坯的质量得到了有效控制和改善。     

薄板坯连铸生产SS400钢工艺技术研究

对唐钢薄板坯连铸机生产的SS400钢的生产工艺进行了分析,认为薄板坯连铸机生产的SS400钢,在采取了精炼站在线定氧,将钢水全氧控制在25×10~(-6)左右,同时连铸采取保护浇注和轻压下等技术后,能够确保薄板坯连铸SS400钢的顺利浇注,轧制的板带材表面质量良好,机械性能符合要求。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

连续镀锌生产线上的纠偏系统

本文介绍了广东南方镀锌板有限公司1＃连续热浸镀锌生产线采用的纠偏系统，分析了它的工作原理以及达到最佳控制的方法     

糖厂现用连续离心机的研究及生产实践

在各糖厂现用连续离心机原有生产实践基础上，对其机械吸震、加温、布温、机索结构、物料密封、机座等部件做了进一步改进，并取得可观的实效。     

快速烧结法制备连续碳化硅纤维

通过熔融纺丝，不熔化处理制得连续聚碳硅烷（ＰＣＳ）不熔化纤维，采用快速烧结方法制备出性能较好的连续ＳｉＣ纤维。探讨了气封条件的选择，以及烧结速度对ＳｉＣ纤维的组成，结构及性能的影响。结果表明，快速烧结条件下，可以实现向纤维上施加张力以及纤维的无机化转变，烧结速度加快会降低纤维的Ｃ／Ｓｉ（原子比），同时有利于提高纤维的抗拉强度和热稳定性。     

唐钢第二炼钢厂CAS—OB精炼站设计及相关工艺技术措施

结合唐钢第二炼钢厂的条件和ＣＡＳ－ＯＢ工艺的技术特点，提出了二炼钢厂建设ＣＡＳ－ＯＢ精炼靖的技术参数，工艺流程和布置方案对精炼站设计吕的若干技术措施提出了解决办法并提出了需进一步研究的几个问题。     

PVDF中空纤维滤膜的形态结构

用Ｌ－Ｓ相转换法制备了聚偏氟乙烯（ＰＶＤＦ）中空纤维不对称滤膜。铸膜液由聚合物、溶剂和添加剂组成。用电子显微镜（ＳＥＭ）考察了聚合物浓度、添加剂用量及种类对膜形态结构的影响。实验结果表明，聚合物浓度对膜形态结构有显著影响，当铸膜液中聚合物浓度较低时，无论用什么种类添加剂，都能形成大、且多的孔，但孔的形状随添加剂不同而异。当恒定聚合物浓度时，添加剂的用量对膜形态结构有很大的影响，但孔的大小及多少与添加剂含量的多少不成正比。