富集化合金层对铝阳极氧化膜的影响

在铝合金与氧化膜的界面的富集化合金层，对阳极氧化膜的局部和整体结构、膜的组成以及性能有重大影响。因此，对铝合金富集化进行预测很有必要。     

铝合金凝固过程的声发射及氢气析出过程

采用声发射测试技术,对Al-Si和Al-Cu系合金凝固过程进行监测,证实合金在凝固过程中存在声发射现象,表现为两个声发射信号计数率峰,两个峰的总计数都随着合金中气体含量增加而增高。本文对Al-Si,Al-Cu合金系产生声发射现象的机理进行了探讨,同时,借助其它实验手段证实了声发射信号与合金凝固中气体析出有很好的对应性。第一个计数率峰与气泡在枝晶臂间形核相吻合。第二个计数率峰与凝固末期的枝晶间拉裂现象相对应,可能是氢在枝晶间析出和聚集产生高压氢导致的拉裂。     

Observations on the role of oxide scales in high-temperature erosion-corrosion of alloys

The results are presented of exposure to a controlled high-temperature erosive gas stream of a series of alloys, which were selected to represent the range of microstructures and mechanical properties available in commercial high-temperature alloys. Analysis of the kinetic and morphological data suggested that the high-temperature oxidation behavior of a given alloy plays a very important role in determining its erosion-corrosion behavior under the conditions studied. In terms of relative behavior, alloys which are weak but ductile at temperature, and which form tenacious oxide scales, exhibited the highest resistance to high-temperature erosion-corrosion. Simple models were developed to describe the expected interaction between high-temperature oxidation and erosion.     

Evaluation of high Ni-Cr-Mo alloys for the construction of sulfur dioxide scrubber plants

Corrosion in wet lime/limestone systems used for flue gas desulfurization in thermal power plants is of great concern. The frequent variations in acidity and in chloride and fluoride ion concentrations experienced by such systems pose a serious threat to the materials of construction. Currently used materials mostly type 316L stainless steel often fail to meet their life expectancy. The present study evaluates the performance of advanced Ni- Cr- Mo alloys 59 and C- 276 in a simulated sulfur dioxide scrubber environment. Accelerated tests showed that high Ni- Cr- Mo alloys have little tendency to leach metal ions such as chromium, nickel, and molybdenum at different impressed potentials. Scanning electron microscopy was used to examine the morphology of pitting attack.     

High-temperature sulfidation of Fe-30Mo alloys containing ternary additions of Al

Fe-30Mo alloys containing up to 9.1 wt% Al were sulfidized at 0.01 atm sulfur vapor over the temperature range of 700–900°C. The sulfidation kinetics followed the parabolic rate law for all alloys at all temperatures. For alloys containing small and intermediate amounts of Al (<4.8 wt.%), a duplex sulfide scale formed. The outer layers of the scales were found to be relatively compact FeS in all cases; whereas the inner layers were composed of the layered compound MoS ₂ (intercalated with iron), the Chevrel compound Fe _x Mo ₆ S ₈,a spinel double sulfide Al _x Mo ₂ S ₄,depending on the Al content of the alloy and the sulfidation temperature. Extremely thin scales were found on the alloys with higher Al contents. Accordingly, extremely slow sulfidation rates were observed—even slower than the sulfidation rate of pure Mo. The transition of the sulfidation kinetics from a high-rate active mode to a low-rate passive mode requires both a critical Al content in the alloy and a critical Mo content. Because of the two-phase nature of the alloys, the latter requirement implies a critical volume fraction of the intermetallic second-phase in the alloy, which has been known as the multiphase effect. Interestingly, the multiphase effect in these alloys was also a function of the Al content in the alloys.     

A1-Li合金的拉伸断裂过程研究

以2090 Ce合金为研究对象，对不同时效时间的室温拉伸断口进行了半定量分析，探讨了拉伸性能对断裂特征的响应关系，重点分析合金分层裂纹的形成过程。研究表明：2090 Ce合金的断裂方式以韧窝、分层开裂和沿亚晶界开裂3种为主，随时效时间的延长，韧窝、分层开裂逐渐减少，沿亚晶界开裂比例逐渐加大：分层开裂程度与时效程度有密切关系：分层开裂过程与试样内部受力状态、晶界状态有密切关系。分层最先发生在试样中心，随后在二分之一、四分之一……处反复发生，最终将试样分割成一系列平行的薄板。时效后期由于亚晶界的弱化，使裂纹倾向沿亚晶界扩展，从而抑制分层开裂的发生，同时导致合金强度，尤其是塑性的下降。     

采用稀土贮氢材料的镍氢电池

介绍了镍-金属氢化物电池的特性和该类电池所用的稀土贮氢材料及其成份配制、制备工艺、合金添加剂对LaNi_5基合金电极综合性能的影响,以及该类电池的应用开发前景。     

Ti—Al二元合金的成分对组织和力学性能的影响

用金相、扫描电镜和X射线衍射研究了6种不同Al含量Ti-Al二元合金铸态和退火态的组织结构和相组成的特征和变化。从结晶动力学的观点,分析了合金的结晶凝固过程。采用三点弯曲方法研究了合金的抗弯性能同Al含量的关系。结果表明,Al含量为34 wt%,经1100℃/30 h退火的合金抗弯性能最好,Al含量偏离34wt%,都对合金的力学性能不利。     

快速凝固Mg94.6Zn4.8Y0.6镁合金薄带的组织与性能

采用单辊快速凝固技术制备了Mg94.6Zn4.8Y0.6合金薄带,研究了薄带的组织及性能特征。结果表明:Mg94.6Zn4.8Y0.6镁合金快速凝固薄带组织由过饱和的单相-αMg固溶体组成,沿厚度方向分为两个晶区:近辊面粗大等轴晶区和自由面细小等轴晶区。Mg94.6Zn4.8Y0.6合金快速凝固薄带的显微硬度为85.95HV,在250℃左右保温2 h的显微硬度最高,超过该温度(250~300℃)显微硬度显著下降。     

High-temperature corrosion and creep of Ni-Cr-Fe alloys in carburizing and oxidizing environments

The carburization of NiCr 32 20 and NiCrSi 60 16 has been studied in CH₄-H₂ mixtures in the temperature range 900–1100°C. The methods included thermogravimetric measurements and studies on reacted specimens by X-ray diffraction, metallographic, and chemical analysis. Upon carburization internal carbides M₇C₃ and M₂₃C₆ are formed (M=mainly Cr); the rate of carburization is determined by carbon diffusion in the Fe-Ni matrix with carbide precipitations. The effect of the alloying elements Ni and Si on the carburization resistance of austenitic alloys is explained. By the same methods the oxidation and carburization in CO-H₂O-H₂ mixtures have been studied. The important role of a stable chromium oxide layer for the carburization resistance was confirmed. Creep tests at 1000°C in a CO-H₂O-H₂ atmosphere where Cr₂O₃ is stable showed carburization occurring through cracks in the oxide layer. At high strain rates premature failure occurs by carburization, which is followed by internal oxidation and formation of cracks, voids, and holes.