VLSI并行测试生成系统的一种动态层次框架

随着VLSI技术的发展和计算机性能的提高,并行测试生成系统不仅必需而且可行,本文在总结已有并行技术的基础上,提出了并行测试生成系统的一种动态层次框架,并给出了一种实现方案。     

A comparative study of three adhesion tests (EN 582, similar to ASTM C633, LASAT (LASer Adhesion Test), and bulge and blister test) performed on plasma sprayed copper deposited on aluminium 2017 substrates

The aim of this study was to compare three adhesion tests carried out on plasma-sprayed copper coatings on aluminium substrates. The first test, the bond pull test, designated EN 582 or ASTM C633, involves a uniaxial static stress and is commonly used in the coating industry. The second test, the LASAT (LASer Adhesion Test), is a recently developed technique based on spallation phenomenon due to laser induced shock waves. In this test, the coating delamination results from spallation at the coating/substrate interface due to uniaxial tensile stress. The last test, the bulge and blister test, involves a quasi-static measurement of the crack propagation energy at the coating/substrate interface. These three techniques have been used to evaluate the influences of different process parameters involved in the coating adhesion such as aluminium surface roughness, substrate pre-heating and plasma spray conditions.     

Tensile and fatigue properties of cold and warm compacted Alumix 431 alloy

Abstract

In this experimental study, tensile and fatigue properties of the Alumix 431 alloy (Al, Zn, Mg and Cu alloys) produced using the conventional press and sinter processes in different pressures and temperatures are investigated. The results clearly showed that the warm compacted specimens can reach the mechanical properties of the cold compacted ones under less pressure. In the fatigue tests it was observed that fracture started from large pores as shown in all scanning electron microscope (SEM) examinations and ductile fracture occurred. 85% of the 180 MPa/80°C and 77% of the 230 MPa/RT specimens fractured at the machined surface. Tensile and fatigue properties of warm compacted (180 MPa/80°C) and cold (230 MPa/RT) compacted specimens are almost equal at these same densities. This result indicates the economic benefit of warm compaction by the much lower applied compaction pressure.     

Internal models of reaching and grasping

One of the most distinguishing features of cognitive systems is the ability to predict the future course of actions and the results of ongoing behaviors, and in general to plan actions well in advance. Neuroscience has started examining the neural basis of these skills with behavioral or animal studies and it is now relatively well understood that the brain builds models of the physical world through learning. These models are sometimes called 'internal models', meaning that they are the internal rehearsal (or simulation) of the world enacted by the brain. In this paper we investigate the possibility of building internal models of human behaviors with a learning machine that has access to information in principle similar to that used by the brain when learning similar tasks. In particular, we concentrate on models of reaching and grasping, and we report on an experiment in which biometric data collected from human users during grasping was used to train a support vector machine. We then assess to what degree the models built by the machine are faithful representations of the actual human behaviors. The results indicate that the machine is able to predict reasonably well human reaching and grasping, and that prior knowledge of the object to be grasped improves the performance of the machine, while keeping the same computational cost.     

Synthesis and wear of Al based,free standing functionally gradient materials: effects of different reinforcements

Abstract

In the present study, three aluminium based functionally gradient materials (FGMs), reinforced with different ceramic particulates (silicon carbide, aluminium oxide, and titanium carbide), were successfully synthesised using the innovative gradient slurry disintegration and deposition (GSDD) technique. The results for Al/SiC and Al/Al₂O₃ revealed, in common, an increase in the weight percentage of reinforcement along the direction of deposition, to result in an increase in porosity and microhardness. However, for Al/TiC, the reverse trend was observed, with porosity and microhardness decreasing with increasing distance from the base of the ingot. The porosity levels for Al/TiC were also found to be significantly lower than those ofthe other two FGMs. Thermomechanical analysis of the FGMs showed thatthe average coefficient of thermal expansion of the high reinforcement end was reduced, as compared to the high aluminium end. Sliding wear test results also revealed that the high reinforcement end was more wear resistant than the high aluminium end, except for the case of Al/Al₂O₃. An attempt is made to interrelate the effects of different types of particulates, with microstructural development, microhardness and wear rate results obtained in the present study.     

Coupled heat and fluid flow model and experimental verification of aluminium plate die casting

Abstract

The present work aims to forecast mould filling, void shape, location and size as well as columnar to equiaxed transition (CET) in commercial pure aluminium casting. A model coupling the momentum equations of the fluid flow and heat transfer equations is presented, in which metallostatic pressure, air gap and oxide layer are considered. Different casting parameters were investigated such as casting configuration by varying the plate thickness from 5 to 20 mm, melt superheat from 40 to 120°C, mould preheat up to 200°C and different pouring heads ranging from 0·3 to 0·6 m. Regarding the microstructure and void formation, the approach based on the Niyama criterion, was considered. The experimental verification of the model was achieved by gravity die casting in the form of a rectangular cavity. Voids inside aluminium plate were investigated by X-ray imaging. Microstructure and CET was investigated microscopically. The supposed model proves its validity for mould filling and in detecting the void features and CET.     

Rapid and Cheap Learning by Exploiting Biarticular Muscles — A Case Study With a Two-Dimensional Serpentine Robot

This study is intended to deal with the interplay between control and mechanical systems, and to discuss the 'brain–body interaction as it should be', particularly from the viewpoint of learning. To this end, we have employed a decentralized control of a two-dimensional serpentine robot consisting of several identical body segments as a practical example. The preliminary simulation results derived indicate that the convergence of decentralized learning of locomotion control can be significantly improved, even with an extremely simple learning algorithm, i.e., a gradient method, by introducing biarticular muscles which induce long-distant physical interaction between the body segments compared to the one only with monoarticular muscles. This strongly suggests the fact that a certain amount of computation should be offloaded from the brain into its body, which allows robots to emerge various with interesting functionalities.     

The life of a plant builder in the modern metals industry

Abstract

The 2007 SMEA Celebrity Lecture (Sheffield Metallurgical and Engineering Association) was given by Roy Tazzyman, the outgoing Managing Director of Siemens VAI–UK, on 4 July 2007 at the University of Sheffield, in conjunction with the Association's annual conference. Ken Ridal summarises the proceedings.     

Super mechano-systems project

The super mechano-system (SMS) project is the Grand-in-Aid for COE Research Project, which started is April 1997 at the Tokyo Institute of Technology for the Creation of New Functionality by the Fusion of Control and Mechanisms, and is supported by the Ministry of Education, Sciences, Sports and Culture. The project aims to establish a new discipline by the functional integration of advanced technologies in mechanisms and control. This paper briefly describes the SMS project.     

New structure of automatic torch and new approach for controlling drop transfer in rotating spray welding arc

Abstract

Using computer aided design/computer aided manufacturing technology, an automatic welding system is designed and manufactured for high current, high speed, and high deposition metal arc active gas (MAG) welding. The welding torch structure is evaluated and optimised via the finite element method and practical welding technology experiments. Finally, the process of high deposition MAG welding is investigated, and it is highlighted that on application of a longitudinal magnetic field to the high deposition MAG welding process, a steady metal transfer and drop deposition condition can be achieved, which is suited to the demands of high current, high speed welding technology.