钢表面化学气相沉积TiC晶体的择优取向

本文用化学气相沉积(CVD)法,以TiCl_4-CH_4-H_2为原料气体,在不锈钢表面获得了致密的TiC膜.研究了TiC的成膜速度、表面形貌和晶体择优取向与沉积条什的关系.结果表明,沉积温度T_(dep),碳钛比CH_4/TiCl_4强烈地影响了TiC的成膜速度、表面形貌和晶体择优取向.CH_4/TiCl_4低时,TiC晶体的择优取向为(220):而CH_4/TiCl_4高时,TiC晶体的择优取向为(200).TiC晶体的择优取向主要取决于气氛中活性碳的平衡浓度。     

纳米Cr颗粒对Ni-Mo复合镀层性能的影响

为了研究纳米Cr颗粒对Ni-Mo复合镀层性能的影响,采用脉冲电沉积方法制备具有不同Cr含量的Ni-Mo复合镀层.利用扫描电子显微镜和X射线衍射仪分别观察和分析复合镀层的组织形貌及结构.采用电化学测试和X射线光电子能谱研究复合镀层的析氢性能和耐蚀性能.结果表明:随着镀液中纳米Cr颗粒含量的增加,镀层晶粒得到细化,析氢过电位增大,复合镀层析氢性能得到提高;当镀液中纳米Cr颗粒含量为20 g/L时,复合镀层表面钝化膜中MoO₃含量较高,且可与Cr产生协同效应,因而复合镀层具有较好的耐蚀性能;但随着镀液中纳米Cr颗粒含量的进一步增加,复合镀层中沉积的Cr元素含量降低,复合镀层的析氢性能和耐蚀性能均降低.因此,当镀液中纳米Cr颗粒含量为20 g/L时,复合镀层具有较好的析氢性能和耐蚀性能.     

表面工程技术在导弹武器装备维修中的应用

本文主要介绍铝/F_(46),协合涂层新技术、复合电刷镀Ni—PTFE新工艺、DJB—823电接触保护剂及三防电子器件绝缘清漆在二炮导弹武器装备维修中的应用。     

The Friction and Wear Properties of CrN, Graphit-iC and Dymon-iC Coatings in Air and under Oil-lubrication.

NITRIDE COATINGS have always been the popularchoice for increasing the wear lifetime for industrialcomponents.TiN is the most widely accepted butrecently CrN has been gaining more interest due itsthermal stability and good performance in corrosiveenvironments.Knowledge of the tribologicalperformance of CrN coatings in dry and lubricatedconditions is still quite limited[1,2].Many authorshave studied the properties of diamond like carbon(DLC)films and how they perform in dry conditions[…     

环氧树脂流变学的研究进展

综述了近20年来环氧树脂流变学的研究进展。利用流变学来指导环氧树脂的最新应用,包括环氧树脂电子浆料例如底部填充胶（underfill）,环氧树脂基复合材料,环氧树脂涂料,环氧树脂黏合剂,环氧树脂与其他树脂/橡胶的复合体系等。环氧树脂体系中的填料规格、加入量以及环氧树脂的固化过程与黏度等流变指数息息相关。随着芯片等领域技术的快速发展,流变学在环氧树脂中的应用还会得到进一步加强。     

片状变燃速发射药燃烧性能的数值计算

为研究包覆方式对片状发射药燃烧性能的影响,建立了不同包覆方式下多层片状发射药的物理模型,并推导了形状函数和燃气生成猛度表达式,利用Matlab软件对不同的宽厚比、长厚比及多层结构的片状发射药进行了数值计算;制备了不同长厚比的片状变燃速发射药,并进行了密闭爆发器实验。结果表明,四面包覆和全包覆可以很好地消除临界宽厚比对片状发射药燃烧性能的影响;与两面包覆的片状发射药相比,四面包覆和全包覆的片状发射药能够延缓内层药减面燃烧的时间,其燃气生成猛度的阶跃程度分别提高了1.17%和1.23%,呈现出良好的燃烧渐增性。     

金属陶瓷防腐蚀涂层替代镀镉或镉−钛工艺的研究

针对钢制零件采用镀镉、镀镉?钛工艺存在氢脆、镉脆风险及不利于环境保护的现状,研究采用涂覆IPcote9183或IPcote9183+IPseal9184形成金属陶瓷防腐蚀涂层(MCAC)的替代工艺。对比结果表明:上述2种金属陶瓷涂层的氢脆性和耐蚀性优于镉及镉?钛镀层,其他性能相当,能够完全替代它们应用于起落架钢制零件的表面防护。     

采用不同模型预测低碳Fe–Ni合金等离子熔覆层的冲击韧性

采用等离子熔覆法在Mn13高锰钢上制备了低碳Fe-Ni合金层。以熔覆电流、喷头移动速率、离子气流量和热处理温度作为输入参数,以冲击韧性作为输出参数,建立了BP(误差反向传播)神经网络模型和粒子群算法优化(PSO)BP神经网络模型,并跟冲击韧性与热处理温度之间的线性回归模型进行对比。结果表明,线性回归模型、BP神经网络模型和PSO-BP模型的平均相对误差分别为7.06%、6.12%和3.03%。PSO-BP模型的预测结果与实测值的误差较小。     

聚酯型粉末涂层附着力异常的原因分析

针对热镀锌板表面聚酯型粉末涂层附着力异常的问题,对比了涂层脱落和正常前处理的基材表面形貌、元素组成、清洁度和红外光谱,得出涂层附着力异常的原因为基材表面在喷涂前发生氧化和油污未除净,给出了相应的解决措施。     

A Strategy of Liquid-Grafted Slippery Sponges with Simultaneously Enhanced Absorption and Desorption Performances for Crude Oil Spill Remediation

Crude oil spill accidents pose a worldwide environmental threat. Oleophilic and hydrophobic absorbents that can selectively absorb oil from water have shown promising application potential in oil spill remediation. Simultaneous optimization of the absorption and desorption speed of absorbents towards oil is highly desirable for their recyclable usage, but remains a great challenge, because these two properties are generally conflicting. Here, a facile and ingenious strategy is proposed to tackle the above challenge via surface modification of porous sponges with highly flexible linear polydimethylsiloxane (LPDMS) brushes. The LPDMS brushes feature liquid-like properties at room temperature owing to its extremely low glass transition temperature, and act as a covalently-grafted lubrication layer throughout the 3D network channels of the sponge, which can minimize contact angle hysteresis and reduce friction between oil and sponge channel. Compared to the prevalent cross-linked polydimethylsiloxane (CPDMS) modification strategy, sponges modified with LPDMS brushes not only shows significantly enhanced absorption speed, but also exhibits superior desorption dynamics towards viscous crude oils. The design strategy of slippery sponges with liquid-like molecules may open a new avenue for developing advanced absorbents with simultaneously enhanced absorption and desorption performances for liquid separation and purification applications.