T8钢—聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性，磨料磨损性及土壤的减粘降组性能，与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％－－２２．２７％。     

胜利油田污水储罐腐蚀防护方法评价

对胜利油田纯粱采油厂A3钢制生产污水（水温约60℃）储罐使用寿命过低的原因进行了实验考察。水质分析数据表明氯离子浓度高（45-48gm）是污水腐蚀性强的主要因素。A3钢在60℃污水中的腐蚀速率，由极化曲线数据计算的值大大高于失重法测定值，敞开系统中失重法测定值又高于密闭系统中测定值，挂片上出现蚀孔，说明储罐中A3钢发生了氧存在下氟离子引起的局部腐蚀（孔蚀）。元素分析结果表明．储罐阴极保护所用的牺牲阳极铝材含铁等元素量超标。牺牲阳极密封不良，在实验污水中7天后电流效率仅为2．92％，失去阴极保护能力。处于实验污水环境中的有涂层保护的A3钢．14天后出现腐蚀极化电流，表明涂层已失去完整性。要提高该采油厂及胜利油田其他采油厂污水储罐的使用寿命，必须改用合格的牺牲阳极和保护涂层材料。图3表2参7。     

高强度钢的Zn—Ti合金新镀层

本文研究了一种Ｚｎ－Ｔｉ合金新镀层，经盐水浸泡、中性盐雾和大气暴露试验结果试验，其耐蚀明显超过镀Ｚｎ层，并与镀Ｃｄ层相近，用缺口持久拉伸试验检验氢脆性，拉伸持续时间超过２００ｈ，达到原航空部部颁标准（ＨＢ５０６７－８５），该镀层适用于高强度钢防护。     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Effects of Substrate Temperatures on the Structure and UV-shielding Properties of TiO_2-CeO_2 Films Deposited on Glass by Radio-frequency Magnetron Sputtering

1Introduction Theultravioletrays(UV)insunlight(-4%)cantransmitintoroomthroughcommonfloatglass,theUVcanmakethematerialsintheroom,eg,paper,furni ture,textilefabricandplastics,becoloredanddeterio rated.ShieldingfromUVirradiationisofinterestinmanyfields.Formu…     

Asbestos replacement aspects: Modification of the fibre-matrix interphase in lonomer based composites

Asbestos fibres, of the chrysotile variety, and chopped carbon fibres were pretreated by an in-situ polycondensation technique eventually resulting in a polyamide coating on the fibre surface. Ionomer based composites containing either carbon or asbestos fibres in random in plane fibre orientation were prepared, and the influence of this coating process on the tensile properties was investigated. It was found that for the asbestos-filled composites the presence of the nylon 6,6 interlayer improves the tensile performance, especially at moderate polyamide depositions. This is not the case with the pretreated carbon-filled composites for which carbon fibres with higher polyamide contents are preferred. Combinations of the treated asbestos fibres with carbon and/or aramid fibres may be used to reduce the asbestos content in asbestos-only based engineering plastics.     

乳胶漆的市场现状和发展前景

对乳胶漆的生产现状，产品结构以及研究开发情况作了简单的综述，并展望了乳胶漆的发展前景。     

压敏显色微胶囊及其涂料的研究进展

综述了无碳复写纸的结构类型和性能、压敏显色微胶囊制备及其微胶囊涂料的最新进展。揭示了微胶囊技术在无碳复写纸应用中的重要作用。     

WF40防腐蚀涂料在原料水罐上的应用

中国石化股份有限公司洛阳分公司炼油厂污水汽提装置的原料水罐(V303)由于接触的污水中含有H2S,NH3,CO2,CN-,酚等多种腐蚀介质因此经常发生腐蚀泄漏事故。经涂刷WF40玻璃鳞片防腐蚀涂料后,已平稳运行两年。2002年检修检查,涂层完好,仍在继续使用。WF40涂料为环氧型玻璃鳞片涂料,其热膨胀系数与钢质基体接近,因此具有耐热冲击性强等优点。待涂罐体经喷砂除锈到Sa2.5级后,涂底漆2道,中间涂层2道、面漆2道,使干膜厚度达到350μm,可有效防止腐蚀性介质的渗透。