Decentralized energy supply: Suitability for the UK's industrial sectors

From the results reported here it is suggested that policy decisions about the potential contribution of decentralized energy supply systems to UK industrial energy requirements should be based on the suitability of individual sectors rather than averaged over all sectors. The suitability of decentralized energy sources is evaluated, based on a themodynamic match between source and demand. This suitability criterion is used to identify the most appropriate sector in manufacturing industries for the adoption of decentralized energy supply, leaving aside economic cost considerations and individual site requirements.     

石家庄市室内氡及其子体浓度

本文报道了用双滤膜法对石家庄市室内空气中氡及其子体浓度的调查结果。47个房间室内氡年平均浓度为17.0Bq·m~(-3),氡子体平均浓度是7.14Bq·m~(-3)。氡及其子体浓度的日变化是清晨4—8时出现峰值。季节变化是夏秋季低,冬季高,全年的最低值出现在8月,最高值出现在11月。     

Performance of compression/absorption hybrid refrigeration cycle with propane/mineral oil combination

This paper discusses the feasibility of a vapor compression/absorption hybrid refrigeration cycle for energy saving and utilization of waste heat. The cycle employs propane as a natural refrigerant and a refrigeration oil as an absorbent. A prototype of the cycle is constructed, in which a compressor and an absorption unit are combined in series. The performance of the cycle is examined both theoretically and experimentally. Although the solubility of the propane with the oil is not enough as a working pair in the absorption unit, the theoretical calculation shows that the hybrid cycle has a potential to achieve a higher performance in comparison with a simple vapor compression cycle by using the waste heat. In the experiment, the prototype cycle is operated successfully and it is found that an improvement of an absorber is necessary to achieve the good performance close to the theoretical one. The application of an AHE (absorber heat exchanger) can reduce the heat input to a generator. Further examinations on some other combinations of refrigerant/refrigeration oil and additives are desirable.     

标准椅全身计数器对不同年龄组均匀体模源全能峰效率的刻度

本文介绍了用标准液体源均匀充入聚氯乙烯制的体模,刻度标准椅全身计数器〔φ8″×4″(NaI)〕的方法和结果。分别就代表6个年龄组的体模,测定了标准椅全身计数器对5种能量(364,637,898,1460和1836keV)γ射线的全能峰效率;给出了全能峰效率与γ射线能量和被测对象体重的关系曲线。     

积极开展泵站技术改造

为探索山丘地区中小型泵站技术改造的经验，选定南康县四个小型泵站作为泵站改造的试点站，进行现场测试，根据测试成果，分析各站存在的问题及效率偏低的原因，并拟定各站技术改造的措施，经实施后取得了较好的效果，本文就南康县泵站改造的实际效果阐明泵站改造的必要性及其改造过程中值得注意的问题。     

Energy pricing policies in developing countries

Government energy pricing policies have multiple and often conflicting objectives: economic efficiency, government revenues (for both parastatal supply companies and the treasury), maintenance or improvement of income distribution, promotion of particular sectors (such as industrial exporters and local resource development) demand management and security of supply. It is important to examine the impacts on and the trade-offs between these objectives resulting from alternative policies in order to assist in policy selection. This article discusses the more important objectives and their conflicts and outlines an approach for the quantitative examination of alternative policies.     

Thermodynamic analysis of solar photovoltaic cell systems

The thermodynamic characteristics of solar photovoltaic (PV) cells are investigated from a perspective based on exergy. A new efficiency is developed that is useful in studying PV performance and possible improvements. Exergy analysis is applied to a PV system and its components, and exergy flows, losses and efficiencies are evaluated. Energy efficiency is seen to vary between 7% and 12% during the day. In contrast, exergy efficiencies, which incorporate the second law of thermodynamics and account for solar irradiation exergy values, are lower for electricity generation using the considered PV system, ranging from 2% to 8%. Values of “fill factors” are determined for the system and observed to be similar to values of exergy efficiency.     

Energy Saving in Industrial Wood Drying Addressed by a Multiscale Computational Model: Board, Stack, and Kiln

This article proposes a multiscale computational model able to calculate energy consumption in a batch lumber kiln. A dual-scale computational model of wood drying deals with the boards/stack interaction and serves as a basis for the present work. A new module was added here that calculates heat losses through kiln walls (convection, condensation) and the energy used by each kiln component (fans, heating elements, humidifier, vacuum pump, etc.). The corresponding mathematical formulation is presented and then theoretical results are compared to those collected in an industrial vacuum kiln. As application example, the effect of air reversal, air velocity, and kiln insulation are exhibited, which depicts the great potential and prospects of this new tool for energy savings in relation to the product quality.     

Energy conservation in the industrial sector of developing countries

This paper begins by examining the most energy-intensive industries and methods by which fuel efficiency can be improved. Next the author analyses the economics of energy conservation using specific case studies drawn from India. It is shown that investing in energy efficiency is more economical Btu per Btu than investing in the enhancement of domestic energy resources. The author also assesses changes in the economics of conservation for private firms when there are government incentives. Finally government policies that can overcome economic and non-economic disincentives for investing in energy conservation are examined.