不锈钢管道坡口加工的新方法

对于不锈钢管及合金钢管坡口的加工,采用以往的加工方法切割出来的坡口一般参差不平、比较粗糙,难于打磨平整。使用LGK空气等离子切割机和磁力管道切割机的组合加上一定的辅助手段,改善了不锈钢管及合金钢管的坡口加工效果,使加工出来的坡口像碳钢管一样平整,更加容易打磨组焊。文章介绍了这一新方法所用的设备、材料、切割原理以及操作过程。     

水泥砂浆衬里在输水钢管内壁防腐中的应用

结合工程实例,阐述了在输水水质腐蚀性不大的情况下,输水钢管的内壁防腐采用水泥砂浆衬里的必要性和优点,并介绍了设计要点和安装施工注意事项。     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

Failure mode transition and energy dissipation in naturally occurring composites

The microstructural aspects of compressive inelastic deformation in balsa wood are investigated with emphasis on the failure mode transition and its effects on energy dissipation characteristics. The architectural features as well as the composite character of cell wall ultrastructure are discussed in a framework to understand the complex interrelationship between microstructure and macroscopic behavior in this extremely lightweight cellular biocomposite. Based on this discussion and experimental results, it is concluded that the biomimetic approach may prove to be a viable strategy in designing composite structures with high specific energy absorption capacity.     

石墨炉原子吸收光谱(GFAAS)法测定石英玻璃中硼的研究

试样经氢氟酸分解，通过加入化学改进剂和多次注射浓缩样品及低温、长时间灰化的方法，在硝酸介质中用石墨炉原子吸收光谱法(GFAAS)测定石英玻璃中硼的含量。该方法解决了GFAAS法分析石英玻璃中硼灵敏度低和准确度低的问题。     

Gamma-irradiation-induced Ag/SiO2 composite films and their optical absorption properties

Small Ag particles or clusters dispersed mesoporous SiO₂ composite films were prepared by a new method: First the matrix SiO₂ films were prepared by sol-gel process combined with the dip-coating technique, then they were soaked in AgNO₃ solutions followed by irradiation of γ-ray at room temperature and in ambient pressure. The structures of these films were examined by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), and optical absorption spectroscopy. It has been shown that the Ag particles grown within the porous SiO₂ films are very small, and they are isolated and dispersed from each other with very narrow size distributions. With increasing the soaking concentration and an additional annealing, an opposite peakshift effect of the surface plasmon resonance (SPR) was observed in the optical absorption measurements.     

珠光体球化的分形研究

珠光体球化反映到金相上，是一种不规则图像的变化，并且具有分形的特征，可望用分形几何的方法来进行描述。以Cr-Mo钢的珠光体球化为例，用分形维数来描述珠光体球化程度；用小岛法对15CrMo钢的珠光体球化图谱进行了测量。实验表明，珠光体球化从1级到6级，其相应的分形维数范围为1.3156-1.9282。从电厂运行了10^5h的15CrMo钢管上取样，实测了该试样的珠光体球化等级，结果表明，以分形维数表示的球化程度与按图谱评定的球化等级完全吻合。     

数字下变频器GC1012B原理及配置方法

数字下变频技术是软件无线电的一项核心技术,其性能的好坏直接影响数字接收机的精度。GC1012B是美国TI公司推出的新型数字下变频器。文中从GC1012B的结构特点和内部功能框图出发,分析其工作原理,并介绍GC1012B几个主要寄存器的配置方法,从而实现对频率、滤波模式、增益大小等参数的设置。最后给出了一个具体配置实例作为参考。     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

浅谈无缝钢管的壁厚偏差

通过探讨、分析无缝钢管壁厚偏差产生的原因，提出了改善钢管壁厚偏差的一些措施，并结合实际生产，得出了比较满意的结果。