多通管塑挤胀形工艺的力学分析

讨论了以聚氨酯橡胶棒为胀形介质，采用塑挤胀形复合工艺把无缝管坯一次成形为多通管成品的加工方法，分析了多通管塑挤胀形过程，提出了“应变样条”分析法，进而分析了典型剖面上应力应变状态，讨论了成形力间应具备的合理的数值关系，以使变形区处于最有利于变形的超高的静水压力和合适的偏应力状态，获得尽可能长的支管。     

TC4合金管材挤压成型工艺研究

研究了不同的挤压温度、挤压比和挤压速度等挤压参数对TC4合金管材挤压成型工艺的影响,以及润滑方式对TC4合金挤压管材表面的影响。研究结果表明,采用热挤压方式生产φ47mm×3mmTC4合金管材,挤压比应选在3￣10之间,挤压速度选在50￣120m/s,润滑剂用玻璃粉,可得到显微组织为两相加工组织,变形充分均匀,力学性能匹配良好,表面质量合格的TC4合金管材。本研究得到的TC4合金管材挤压成型工艺研究可用于工业化生产。     

板料成形优化技术进展与质量工程研究

板料成形过程的优化研究对于改进模具设计、提高产品质量具有重要意义。综述了板料成形工艺优化的研究现状。考虑到在有约束的设计优化中,最优结果常位于约束边界附近,随机因素的波动易导致产品质量不稳定甚至失效,难以保持产品的可靠性和稳健性。为此,本文应用质量工程学中的6σ理念,提出了基于数值模拟的板料成形6σ稳健设计优化方法。     

LF6铝合金的超塑性和扩散连接的组合工艺

研究了ＬＦ６铝合金的超塑性和扩散连接组合工艺，试验结果表明；预先采用变形再结晶的方法细化材料的晶，并有效地去除铝合金的致密氧化膜，即可成功地实现铝合金的ＳＰＦ－ＤＢ组合工艺。利用电子探针从微观观察了扩散连接接头的界面扩散行为，并首次从机理上分析珥金属的超塑性和扩散连接两种工艺之间的内部联系。     

An Incremental Roll Forming Process for Manufacturing Doubly Curved Sheets from General Quadrilateral Sheet Blanks with Enhanced Process Features

In order to manufacture a doubly curved sheet metal effectively, a flexible incremental roll forming process has been developed by adopting the advantages of the incremental forming process and the roll forming process by combining inherent flexibility of the incremental forming process and continuous deformation of the roll forming process. In the proposed roll forming system, a newly designed gripper system is attached in order to achieve automation and more precision manufacturing of the required sheet intended double curvature. The forming method has been further enhanced to form general quadrilateral blanks (including a square, a rectangle, a symmetrical trapezoid and an asymmetrical trapezoid, etc.) into doubly curved shapes by controlling the forming schedule developed by various experiments.     

有限元模型转换及其在金属板料成形数值模拟中的应用

本文根据CAD和CAE软件各自的功能和特点 ,探讨了板料成形数值模拟中CAD模型向CAE模型转换的方法 ;并针对有限元分析软件ANSYS与ABAQUS的实际特点 ,编写了有限元模型转换接口程序 ,用实例验证了所编接口转换程序的可行性与正确性。     

Effects of temperature and blank holding force on biaxial forming behavior of aluminum sheet alloys

Biaxial forming behavior is investigated for three aluminum sheet alloys (Al 5182 containing 1% Mn (5182+Mn), Al 5754, and 6111-T4) using a heated die and punch in the warm forming temperature range of 200–350 °C. It is found that, while all three alloys exhibit significant improvement in their formability compared with that at room temperature, the non-heat-treatable alloys 5182 + Mn and 5754 give higher part depths than that of heat-treatable 6111-T4. The formability generally increases with decreasing BHP (BHP), but increasing the forming temperature and/or BHP minimizes the wrinkling tendency and improves the forming performance. The stretchability of the sheet alloys increase with increasing temperature and increasing BHP. For the alloys and forming conditions involved in the current study, the formability, measured in terms of part depth, comes mainly from the drawing of metal into the die cavity, although stretching effects do influence the overall forming behavior. The optimum formability is achieved by setting the die temperature 50 °C higher than the punch temperature to enhance the drawing component. Setting the die temperature higher than the punch temperature also improves the strain distribution in a part in such a manner that postpones necking and fracture by altering the location of greatest thinning.     

金属塑性成形过程的微观组织模拟与优化技术研究现状

介绍了金属塑性成形过程中微观组织演变的数学模型和常用的微观组织优化目标函数 ,给出了金属塑性成形微观组织模拟和优化的主要方法———微观遗传算法和灵敏度分析方法的基本原理 ,叙述了近年来国内外金属塑性成形微观组织模拟与优化研究概况。     

304不锈钢精铸件点缺陷的形成与控制

针对典型304不锈钢精密铸件内出现的黑色点缺陷,对其表面形貌、成分进行了分析,并在此基础上总结了缺陷的形成机制,确定了相应的防止措施。研究结果表明,铸件内的点缺陷可以划分为两类:一类具有不规则截面,为脱蜡过程中剩余腊料的燃烧残留物;另一类为熔炼过程中,由于脱氧剂和除渣剂的去除不彻底而引入的夹杂。通过优化脱蜡和熔炼工艺,使得铸件内的点缺陷得到了很好的控制。     

冷镦挤复合的连接成形工艺分析及模具设计

基于镦挤连接成形的金属塑性变形规律,分析了一次连接成形件的冷镦挤复合成形的形变特点和工艺特点,进行了冷镦挤一次连接成形工艺过程的可行性分析设计和模具设计,并得到了生产实践验证。