最大熵在感应测井反演中的应用

常规的反演方法是对感应测井资料进行线性反褶积。由于感应测并获得的响应曲线是地层非线性时变滤波的结果,感应测井响应随地层电导率发生非线性变化。本文把熵的概念引入到感应测井反演中。用最大熵方法分别设计出实部信号和虚部信号所对应的反滤波因子,两条反映测井响应随电导率非线性变化的非线性函数也被拟合出来。文章最后用设计出的滤波因子及被拟合出的非线性函数对模拟相量感应测井资料进行了相量反褶积。处理结果表明,围岩效应和趋肤效应基本被消除。本方法与常规的三点反褶积法相比,克服了过聚焦现象,提高了精度。     

铝合金高速船船体建造工艺

简述了ＬＦ１５和ＬＦ１６两种新型船用耐蚀可焊铝合金及其配套焊接材料在实船建造中的应用情况。阐述了铝合金全焊结构船体建造的关键技术及我国铝船体建造的３种方法     

Analysis and Optimization Laminar Viscous Flow Through a Channel

Optimizing of laminar viscous flow through a pipe by two dimensionless values is investigated analytically. Dimensionless entropy generation and pumping power to heat transfer rate ratio are used as basis for constant viscous and the temperature dependence on the viscosity. For this matter we calculate entropy generation and pumping power for a fully developed in a pipe subjected to constant wall temperature for either constant viscosity and the variable viscosity. The variation entropy generation increase along the pipe length for viscous fluid is drawn, either the variation summation dimensionless entropy generation and the pumping power to heat transfer rate ratio are varying the fluid inlet temperature for fixed pipe length and are varying pipe length for fixed fluid inlet temperature are drawn. For low heat transfer conditions the entropy generation due to viscosity friction becomes dominant and the dependence of viscosity with the temperature becomes essentially important to be considered.     

简易高性能纳秒脉冲发生器

为了实现电子散射飞行时间谱仪电子束的脉冲化及产生时一幅变换器的启动或停止信号。我们利用开关晶体管的雪崩特性研制了一个性能好，成本低的纳秒脉冲发生器。该发生器输出上升时间好于Ｉｎｓ，幅度达１０Ｖ的负尖脉冲，用作时一幅变换器的启动或停止信号；也输出上升时间约３ｎｓ，幅度５－３０Ｖ连续可调和宽度５－２３０ｎｓ可调的正脉冲，用作电子束脉冲化的调制信号，脉冲重复率为１５０×１０＾３ｓ＾－１。它可广泛用于类似     

高纯锗探测器的快定时性能及其应用

为了将高纯锗（ＨＰＧｅ）探测器用于快定时的物理实验中，本实验研究厂影响高纯锗探测器定时谱仪时间性能的各种因素，找出了获得谱仪最小时间分辨的各种最佳参数。并建立了分辨时间为４．１９ｎｓ，能量分辨率为２０ｋｅＶ，微分非线性好于±２．０％，计效率可承受１２０×１０￣３ｓ￣（－１）的时间微分扰动角关联谱仪。利用此谱仪，以￣（２０４）Ｂｉ为探针核，研究了Ｂｉ系高温超导的微观机理，取得了较好的结果。     

回火处理对高碳冷拔钢丝强度和塑性的影响

研究了６５钢冷拔钢丝在５００℃不同时间回火时的抗拉强度和延伸率的变化。试验结果发现，在回火初期，抗拉强度首先增长，然后随口火时间的延长连续降低，而延伸率始终在增长，增长速度是先快后慢。这种行为可归因于第一内应力的消除和ε－碳化物在形变铁素体中的析出以及后来再结晶的发生。     

Thermography of aged contacts of high voltage equipment

New developments in diagnostic tools and systems are necessary for a reliable and economic evaluation of the condition of equipment in power systems. In a research project a tool for the condition of contacts of centre break disconnector, which is used under normal operation by the aid of a thermography measurement system, has been developed. In this paper, an overview about the laboratory investigation of the temperature load behaviour and the environmental influence on-site for new and aged disconnector contacts are given. A condition evaluation tool for contacts, which was the aim of the project, has been created. The basic method for the evaluation is presented, and also two additional easements for a fast identification of suspect contacts are presented. With this evaluation tool and the usage of a thermography based measuring system, a condition based maintenance strategy can be applied, whereby an early detection of damages is possible and so power quality and reliability increase.      

An Electronic Approach to Materials Design

A molecular orbital approach to materials design has recently made great progress. This approach is based on the electronic structure calculations by the DV-Xα cluster method. In this paper recent progress in this approachis reviewed. In particular     

High temperature transport kinetics in heteroepitaxial LaFeO3 thin films

Heteroepitaxial LaFeO₃(1 1 0) thin films with a thickness of 150 nm were grown on LaAlO₃(0 0 1) by reactive sputtering in an inverted cylindrical magnetron geometry. Equilibrium conductivity was measured as a function of partial pressure of oxygen at T=1000 °C, and logσ plotted vs. logP(O₂) showed a minimum in conductivity for P(O₂)=10⁻¹¹ atm and a linear response between 10⁻¹⁰ and 1 atm. This linear response makes thin films of LaFeO₃ a promising material for oxygen sensor applications. We have also measured the time response of the film conductivity upon an abrupt change in the partial pressure of ambient oxygen from 10⁻² to 10⁻³ atm, which was determined at 60 s for T=700 °C and <3.5 s at T=1000 °C.     

高放废液中^147Pm的测定

建立了高放废液中~(147)Pm的测定方法。用HDEHP萃取稀土,再用HDEHP萃淋树脂柱分离AM和稀土。然后用高效液相色谱法将~(147)Pm从Eu、Ce等其它稀土中分离出来,用液体闪烁法测量~(147)Pm的放射性活度。