Generalized difference control of parallel streams temperatures

A furnace with multiple parallel passes and multiple burners is commonly seen in petroleum refineries. In order to maintain the furnace running in a safe, stable, and high-efficiency state it is necessary to control the outlet temperatures of the multiple passes to be the same. Due to the fact that the process of the oil heating in such furnace is nonlinear, multivariable, time varying, has serious coupling among passes, has frequent dynamic changes and a large time delay, traditional control methods have trouble in controlling these temperatures, and some advanced control methods, including predictive control, adaptive control, and robust control, are usually too complex for convenient use. In this paper, a control technique, called differences control technique (DsCT), is proposed to distribute the stream flowrates such that the stream temperatures are as identical as possible. The principle of the proposed technique is explained and demonstrated, and the results of its application to a real-life petroleum refinery furnace are also reported. The DsCT technique has the following advantages: it does not need complicated design procedures, the controller structure is simple, it is easy to apply, and it can be canonically applied to furnaces with different number of passes.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

微型生化分析仪样品室温度控制系统研究

结合微型生化分析仪样品室的要求,设计了一种基于单片机的微型生化分析仪样品室温度控制系统.它以AT89S51为核心,采用单总线高精度数字温度传感器DS18B20对样品室温度采样,同时利用汇编语言编写温度设定与控制程序,采用半导体制冷的方式,实现了温度在25℃、30℃、32℃和37℃四个温度值的稳定,控制精度达±0.5℃.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Study of hot air generator with quasi-uniform temperature using concentrated solar radiation: Influence of the shape parameters

The non-uniformity of the air temperatures and the slow flow rate at the plane collector exit constitute the main cause of the limitations of the solar drying systems. In order to obtain an uniform and a variable flow rate for different uses, a hot air generator using concentrated solar radiation is proposed. To improve the thermal efficiency of the generator, a study of the influence of different shape parameters is realized. The generator is simulated in the laboratory while investigating the flow induced by a circular disc heated uniformly by Joule effect at constant temperature. This disc is placed at the entrance of an open ended vertical cylinder of a larger diameter. Thermal radiation emitted by the hot disc heats the cylinder wall. The heating of the fluid at the cylinder-inlet generates a thermosiphon flow around the one created by the hot disc. The comparison of the velocity and the temperature profiles of the resulting flow permits to determine the influence of the cylinder height, the vertical source-cylinder spacing and the radius ratio, on the resulting flow at the system exit. Thus, a judicious choice of the shape parameters entails an improvement of the flow rate as well as the thermal flux absorbed by the air and a good homogenization of the air temperature at the generator exit.     

Effect of electric field on the hydrodynamics of fluidized nanoparticles

The effect of electric field on the hydrodynamics of nanoparticles was studied in a fluidized rectangular bed, with electrodes attached to two parallel walls. It was shown that the electric field of the order of 3 times the gravity markedly decreased the bed expansion and increased the solids volume fraction of nanoparticles fluidized by air. In these experiments, a light diode assembly was utilized to infer the local solids volume fractions within a rectangular bed of 10 nm silica particles. These experimental measurements yielded a two dimensional solids volume fraction distribution within the rectangular bed. The experimental results provided some new insights into the distribution of solids within the bed. The agglomerate diameters were computed using a momentum balance with the drag given by the Ergun equation and the empirical Richardson-Zaki method. Both methods yielded agglomerate diameters of the order of 100 μm and showed dependence on the strength of the electric field. The electric field decreased the granular temperature of the nanoparticles.     

Drying Kinetics of a Porous Spherical Particle and the Inversion Temperature

A model is presented for drying of a single porous particle with superheated steam and humid air. Experimental data for spherical porous ceramic particle reported in the literature were used for the validation of the model. An inversion temperature at which the evaporation rates within superheated steam and humid air are equal was predicted. The effect of thermophysical properties of the particle (permeability 10^-14 - 10^-17 m², diameter 3 × 10^-3 - 10 × 10^-3 m) and operating variables (gas mass flux 0.26 - 0.78 kg m^-2 s^-1, drying agent temperature 120-200°C) is tested. The inversion temperature is shown to be affected by the thermophysical properties of the porous particle and of the drying agent.     

蓄热式均热炉生产中存在问题的分析及解决方案

介绍了高温空气燃烧技术在均热炉上的应用情况，对应用中出现的问题进行了分析，并提出了解决方案。     

烧结处理小矿山精矿的应用研究

研究小矿山精矿的性质，分析小矿山精矿对烧结过程的影响，提出了增加小矿山精矿配入量的途径及方法．     

Low temperature synthesis of aluminium titanate by an aqueous sol-gel route

Formation of aluminium titanate (AT) has been achieved at low temperature through sol-gel process using boehmite and titanium hydroxide as precursors by controlling the particle size at nanoscale followed by in-situ peptisation. The formations of AT phase, particle size distributions, sintering and thermal expansion characteristics, and microstructural features have been reported. DTA and XRD analysis have been performed to confirm the formation of AT. A 94% relative density was obtained for aluminium titanate sintered at 1550 °C with controlled grain size in the range of 2-3 μm.